

Know what's even better? Watching molten paraffin wax solidify as it cools down.
I've always thought the Paint Drying Channel totally sucked. Try the Epoxy Curing Channel... much more going on there.
![]()
Know what's even better? Watching molten paraffin wax solidify as it cools down.![]()
I got the night off.
Apparently I said something that pissed her off.![]()

LMAO...Might have been because you slapped her ass and yelled, GIDDYUP TIFFANY!!
![]()





my only way of thinking, about removing anything from a tapered shaft, would be to use a gear puller, with long enough jaws. then you'd have to press it back on. you might be able to press it back on, by simply making some sort of stack of either hard wood, or several bricks, then using the drill press handle, rotate that enough to extend the drill chuck shaft, into the new chuck.BTW about that rat bastard file...
I broke my drill press.
The whole tapered arbor shaft fell out last week when I tried using the 4" hole saw on sheet metal.
It's pressed in, so I simply removed the hole saw, tapped it back in, then rammed the chuck down on a wood block.
It fell out again a minute later and I got pissed and bashed upwards on it with my brake drum hammer.
Well it mushroomed the bottom of it and now the cone shaped things that grab drill bits can't extend below the chuck for bits smaller than 3/8.
So to fix it I took my only rat-tail file and cut the handle off so I could chuck it up in the hand drill and used it to file the mushroomed metal away.
So now it works but it's still tight as f* and I'm not sure how to replace it.
I was busy last night so I simply sent my dad this picture and asked him to see if he can find a replacement chuck on the Google machine.
View attachment 37784
He sent me this link:
South Bend Lathe SB1372 5/8-Inch by JT3 Drill Chuck - Power Drill Chucks - Amazon.com
I don't know how to get the chuck off of the tapered arbor shaft.
I don't even know how to get the arbor back out cuz I bashed it in there pretty good.
On some drills if you look up into the chuck you can see an Allen screw but I didn't see one in mine so I'm thinking it's just a tapered thing and jammed in with force.
![]()
The platform on that drill press can't handle much downward force before it flexes. I'd have to swing it out of the way and stand a piece of 4x4 in there or something.my only way of thinking, about removing anything from a tapered shaft, would be to use a gear puller, with long enough jaws. then you'd have to press it back on. you might be able to press it back on, by simply making some sort of stack of either hard wood, or several bricks, then using the drill press handle, rotate that enough to extend the drill chuck shaft, into the new chuck.
if there is a way for you to use a hydraulic bottle jack, that'll be safer and less stress on the shaft.The platform on that drill press can't handle much downward force before it flexes. I'd have to swing it out of the way and stand a piece of 4x4 in there or something.
Maybe use a piece of wood to protect the new chuck and bash it on with a hammer.
Yeah, in conjunction with a 3 or 4 foot length of 4x4 wooden post.if there is a way for you to use a hydraulic bottle jack, that'll be safer and less stress on the shaft.
you could, but then you also bought steel rods and made jacks with them..????Yeah, in conjunction with a 3 or 4 foot length of 4x4 wooden post.
If you're taking about the little thing I slapped together for un-twisting the wall studs, it's just a piece of threaded rod inside a scrap of electrical conduit.you could, but then you also bought steel rods and made jacks with them..????
oh..ok...that'll bend quick..If you're taking about the little thing I slapped together for un-twisting the wall studs, it's just a piece of threaded rod inside a scrap of electrical conduit.
that's right, Harbor Freight always has nice ones cheap.Just wail on it some more with the hammer. That'll fix it good enough that you'll have an excuse to buy a new drill press.
![]()