Duck Pond Redneckery


Just disconnect the flood for now in case they give you crap about it.
The gas company isn't going to do a full inspection. He's going to say "Yippers, looks good from my house, but unfortunately there's snow and it's cold (whine) so I'll just run a garden hose across the ground and come back in the spring".

I might just pop in a 20 amp breaker for it, or whatever it says in the manual. It's a big 200 amp panel. Plenty of room.
 
I was going to wall up the upper part of the wall above the heater tonight, just because it'll be easier to do before I put in the duct and the flexible gas line.

Went & turned the torpedo back on, went in the house to take a shit, went back out, turned off the torpedo and went to get kerosene.

Saw the Budweiser sign in the window at the gas station and said fuck it.

So now I'm kinda drunk, in the house listening to the soundtrack to Medal of Honor Allied Assault while my army guy is in some Nazi bunker.

I'm taking a break from killing Nazis.
 
You'll run over it, chop it to bits, and blow yerself up.

:eek:

:thefinger:

:D
Yeah, that's why I might trench it myself if the gas company guy is too much of a ***** feline to do it himself.

I don't care. I own a trencher. It just needs tires and a carb cleanout.
 
How much snow are you getting?
The news said that there were 1500 flights canceled there this weekend.
:stare1:
A good excuse to not go to work... its cold and snowing out!

o_O

How come that never worked when you were ten, and still had to go to school?

:mad:
 
A good excuse to not go to work... its cold and snowing out!

o_O

How come that never worked when you were ten, and still had to go to school?

:mad:
because either mom or dad, were stay at home parents, and that if the kid stayed home, the parent at home, could not mess around with the neighbor..????
 
How much snow are you getting?
The news said that there were 1500 flights canceled there this weekend.
:stare1:
Got an inch or two Saturday, not enough to even bother plowing. Then after it stopped, wind blew it around. I've got small drifts here and there.

Yesterday more snow, about the same as Saturday.

My little 8 foot wooden step ladder is outside covered in ice. :mad:
 
I gotta go to Menard's now to get a pair of nuts. :toothpick:

During my crusade against galvanic metal corrosion, the only stainless steel pipe clamp I could find in 4" (diameter you sophomoric imbeciles :mad: ) was a truck style band clamp for vehicle exhaust pipes.

The plan is whatever I rig up to hold the end of my long, stiff pipe will attach via the inch long excess bolt threads on the band clamp.

The band clamp is stainless, the bolts and half-cylinder things are galvanized and the center part is aluminum. :confused-96:

20161210_234619.webp

So,.... :headscratch2:

I'm thinking flattened end of a stick of conduit, drilled and stuck under an extra nut on the clamp.

Those bolts are 7/16 and the biggest I have in my personal hardware store is 3/8.

I'm not too concerned about galvanic corrosion on the clamp. It's easily replaceable, especially since I'm not going to ram it tight with an impact like you do on truck exhaust. It's the 50 dollar section of furnace flue I don't want to corrode.


Which reminds me... on @Blood's green truck we replaced some exhaust stuff and noticed that it was rusted worst at the clamps.

That's because the clamps are stainless steel and the pipe is galvanized. It was designed to fail, imagine that. :mad:

So I guess in the future always use galvanized clamps on galvanized exhaust pipes.
 
I gotta go to Menard's now to get a pair of nuts. :toothpick:

During my crusade against galvanic metal corrosion, the only stainless steel pipe clamp I could find in 4" (diameter you sophomoric imbeciles :mad: ) was a truck style band clamp for vehicle exhaust pipes.

The plan is whatever I rig up to hold the end of my long, stiff pipe will attach via the inch long excess bolt threads on the band clamp.

The band clamp is stainless, the bolts and half-cylinder things are galvanized and the center part is aluminum. :confused-96:

View attachment 37764

So,.... :headscratch2:

I'm thinking flattened end of a stick of conduit, drilled and stuck under an extra nut on the clamp.

Those bolts are 7/16 and the biggest I have in my personal hardware store is 3/8.

I'm not too concerned about galvanic corrosion on the clamp. It's easily replaceable, especially since I'm not going to ram it tight with an impact like you do on truck exhaust. It's the 50 dollar section of furnace flue I don't want to corrode.


Which reminds me... on @Blood's green truck we replaced some exhaust stuff and noticed that it was rusted worst at the clamps.

That's because the clamps are stainless steel and the pipe is galvanized. It was designed to fail, imagine that. :mad:

So I guess in the future always use galvanized clamps on galvanized exhaust pipes.
is that what the mrs told you you gotta grow some nuts:confused-96:. no wonder the heater is not installed your to busy on here and at maynerds playing with the hardware
 
is that what the mrs told you you gotta grow some nuts:confused-96:. no wonder the heater is not installed your to busy on here and at maynerds playing with the hardware
I was literally at Menard's when you posted that. :rolleyes:

I got another piece of sheet metal to finish that square section.

And I got a crappy looking damaged piece of 5/8" drywall for the wall section above it, for $1.47 :cool:.

Everywhere else will be OSB plywood but I think drywall is more appropriate for that part above the heater.

And I'm going to do that before I finish the heater so the flue pipe and gas line won't be in my way.

But not tonight. I'm too hung over. :(

I was feeling totally fine until I got home and turned on the kerosene heater. It failed to ignite and I had to tap my finger over the fuel pressure adjustment thing to get it to light. Then it shot flames for a few minutes & the smell made me come down with a case of the f*kits.
 

Back
Top