Duck Pond Redneckery


Yes, something like that. The pie plate is decorative. It just slides onto the pipe outside and inside and covers any gaps around the pipe. It's not like your putting a hole through an 18th century Victorian house. It's freaking metal barn. Just make a hole and use one of those thimbles and be done with it.

View attachment 37681
A metal barn, right above a door framed in plain old untreated lumber.
 
Found out flue termination can't be within 4 ft of any door. National code.

Also required to be in class 3 pipe which is that single wall stainless.

Clearance to combustibles is 6".

Gonna have to exit over the door, continue out one foot, turn north and go 6 feet, maintaining an upwards slope 1/4" per foot.

Condensation drain is required because cold air on the outside of the single wall duct will cause condensation.

No idea if that drain needs a real actual drain but after the U-trap I'm just going to run it into a bucket.

Heater adapter, drain, 3' pipe, sheet metal for interior wall, thimble, 8 ft pressure treated 4x4 fence post to make a modified version of the Skateboard thing, 90° elbow, two more 3 foot straights, termination tee, tube of high temp silicone.

30+50+50+forgot what thimble costs+whatever the 4x4 costs, +30+55+50+50+50+12

Plus some kind of hardware for holding the end of the flue up.

Going north inside the shop instead of outside will require two elbows instead of one, and require redoing the gas line.


This is going to cost more than the heater itself. :mad:
 
Found out flue termination can't be within 4 ft of any door. National code.

Also required to be in class 3 pipe which is that single wall stainless.

Clearance to combustibles is 6".

Gonna have to exit over the door, continue out one foot, turn north and go 6 feet, maintaining an upwards slope 1/4" per foot.

Condensation drain is required because cold air on the outside of the single wall duct will cause condensation.

No idea if that drain needs a real actual drain but after the U-trap I'm just going to run it into a bucket.

Heater adapter, drain, 3' pipe, sheet metal for interior wall, thimble, 8 ft pressure treated 4x4 fence post to make a modified version of the Skateboard thing, 90° elbow, two more 3 foot straights, termination tee, tube of high temp silicone.

30+50+50+forgot what thimble costs+whatever the 4x4 costs, +30+55+50+50+50+12

Plus some kind of hardware for holding the end of the flue up.

Going north inside the shop instead of outside will require two elbows instead of one, and require redoing the gas line.


This is going to cost more than the heater itself. :mad:
you do realize that you could have bought a MR buddy heater and a 30 LB tank of propane and the connector hose for under 200 bucks right:confused-96: and use the ceiling fan to move the warm air around;)
 
you do realize that you could have bought a MR buddy heater and a 30 LB tank of propane and the connector hose for under 200 bucks right:confused-96: and use the ceiling fan to move the warm air around;)
When you suggested that earlier I dismissed it as simply being clueless because you live in southern California.

This is a 24 x 35 shop with a 12'5“ high ceiling. Even when I'm done with the insulation it's going to take more than a little toy heater.
 
When you suggested that earlier I dismissed it as simply being clueless because you live in southern California.

This is a 24 x 35 shop with a 12'5“ high ceiling. Even when I'm done with the insulation it's going to take more than a little toy heater.
and i thought you were sectioning off an area not that big:confused-96:.. and whats living in so cal got to do with it it gets cold out here:rolleyes:. never mind on the toy heater idea;)
 
Chimney kit costs what? And are you going to get enough draw for that burner?

Chimney won't work right if you do not.
Like 300-something but includes parts we don't need and lacks the ones we do.

It's got a draft inducer fan.
 
So it's gonna cost you double the price just to get the parts you do needo_O
No its not.

Because none of the parts at fucking Menard's fit together.

The 4" class 3 single wall stainless pipe won't even fit in the wall thimble made for 4" class 3 single wall stainless pipe. The hole is like 5" diameter for a 4" pipe.

Who the fuck designs this stuff?
Maybe there's a reason they literally sell duct sealant in 5 gallon buckets.

I've tried getting three different HVAC companies to do it and none of them want the job. If they even answer their fucking phone, as soon as they hear it's a partially completed installation, all of a sudden they're booked up til March or they don't do partial installations because blah blah blah.. .

I even cussed one of them out because I don't fucking pay people to do something I can do myself.

So I don't know what to do besides go get some fucking truck exhaust pipe and fucking weld it to the God damn piece on the furnace, weld it to the fucking thimble, weld the 90 on it and weld up my own fucking termination tee because at least then I know it'll fucking go together and not leak.

Seriously I would like to find out who designs this duct stuff and beat him to death with a hammer. I want to see brains splattered all over the ground.
 
If you were around me the place where I park my truck has a son who builds dragster frames there. He's a metal fabricator also. I've seen him make any pipe with any angle. He even makes the edges that are bent over then snap in place or he welds really thin metal.

The guy that I'm working on that project right now has a PhD in fluid dynamics which covers your exhaust problem. He would be all over you ragging on this and that has to be done this way and that way. You get him going and he won't shut up.

What seems like a simple thing like this can lead you down a path that causes all sorts of problems. I've been there!
 
Also, I don't think it will matter in your case but red necking exhaust on some heating units like a garage used oil heater must be done right or you get flame out all the time when the wind hit's it just right cause you didn't follow the instructions that made absolutely no sense at all
 
No its not.

Because none of the parts at ****ing Menard's fit together.

The 4" class 3 single wall stainless pipe won't even fit in the wall thimble made for 4" class 3 single wall stainless pipe. The hole is like 5" diameter for a 4" pipe.

Who the **** designs this stuff?
Maybe there's a reason they literally sell duct sealant in 5 gallon buckets.

I've tried getting three different HVAC companies to do it and none of them want the job. If they even answer their ****ing phone, as soon as they hear it's a partially completed installation, all of a sudden they're booked up til March or they don't do partial installations because blah blah blah.. .

I even cussed one of them out because I don't ****ing pay people to do something I can do myself.

So I don't know what to do besides go get some ****ing truck exhaust pipe and ****ing weld it to the God damn piece on the furnace, weld it to the ****ing thimble, weld the 90 on it and weld up my own ****ing termination tee because at least then I know it'll ****ing go together and not leak.

Seriously I would like to find out who designs this duct stuff and beat him to death with a hammer. I want to see brains splattered all over the ground.
Umm...

:hide:

If you could do it yerself, y'all wouldn't be on here biotchin' about it.

:D
 
Umm...

:hide:

If you could do it yerself, y'all wouldn't be on here biotchin' about it.

:D
id'e call a professional like he was gonna do in an earlier post. if he thinks doing it himself is expensive have the grease out when you call a professional it will be costly then
 
If you were around me the place where I park my truck has a son who...
You mean the OWNER of the place has a son,... right? o_O

Umm...

:hide:

If you could do it yerself, y'all wouldn't be on here biotchin' about it.

:D
I think the local HVAC companies pay Menard's not to inventory exhaust components that actually fit so you can't piece an entire system together.

Not fucking kidding either. I even looked at the B-vent stuff (only legal for vertical) and the 3" stuff. You seriously can not piece together a whole system with the stuff on their shelves.

I bought $430 worth of that stainless steel shit today only to find out the "universal" appliance adapter made by Mr Fucking Heater won't fit the exhaust outlet on the heater made by Mr Fucking Heater.

Unless you're supposed to butt two identical size pipe ends together and wrap "duct" tape around it.
 

Back
Top