Duck Pond Redneckery


Yeah.

I'm using "clear acrylic sheet".

Same **** I think.

And I'm going to try cutting it with the circular saw like plywood. :D
I had a window glazed with that one time. The heat/cold cycles would cause it to bow in and out well over 1/8" - impossible to keep sealed. It allowed in a major draft. Couldn't wait to get rid of that crap.
 
Yeah.

I'm using "clear acrylic sheet".

Same **** I think.

And I'm going to try cutting it with the circular saw like plywood. :D
i was able to cut plexiglass with a razor knife, much like that is used for wall boards. i had to score the line several times, (using a T square), then after it breaks on the line. then i lightly sanded the edges with about 120 grit sand paper. a saw if not the correct tooth per inch will make shrapnel outta that stuff. not to mention, it'll crack it.

you "might" be able to cut a line with a dremel tool as well. since that is a very high speed tool.
 
I had a window glazed with that one time. The heat/cold cycles would cause it to bow in and out well over 1/8" - impossible to keep sealed. It allowed in a major draft. Couldn't wait to get rid of that crap.
The trick with plastic windows is to use 1/4" or 3/8" trim to hold it on both sides. It's not bowing anywhere that way, and you have a nice deep seal channel.
 
I had a window glazed with that one time. The heat/cold cycles would cause it to bow in and out well over 1/8" - impossible to keep sealed. It allowed in a major draft. Couldn't wait to get rid of that crap.
How big were the panes?

The larger the sheet, the more likely that'll happen.

Mine will be 12" x 4".

I'm not making a real actual window though. I'm just making a box with two layers of plexiglass to go at the top of the west wall to provide some insulative effect where there is a skylight already.

Just translucent white corrugated siding. The plan is to caulk up the seams if possible, and fill the gaps along the top and bottoms caused by the corrugations with Great Stuff to make that effectively become the third pane of a triple pane window.

I'll cut my end slots deeper than the top and bottom ones though. Cuz if it's gonna expand it'll expand more along its length than its breadth.

I am using permeable caulk though. Not the stuff that turns into chalk.
 
The trick with plastic windows is to use 1/4" or 3/8" trim to hold it on both sides. It's not bowing anywhere that way, and you have a nice deep seal channel.
I'm just going cut slots into the 2x6 inner frame. Assemble 3 sides, slide the plexiglass in, then put the top part on & both panes are locked on place.

Plan is to allow for 1/8" expansion vertically & 1/4" horizontally.
 
You can cut plexi with just about any circular blade as long as it's sharp. Secret is don't push it through like a sheet of plywood. Run it through the saw slower so it doesn't melt and gum up the blade. The shallower you set your blade the better. A finer blade works best, but you can use a coarse blade. Just don't force the plexi through the saw. You can smooth the edges with a small orbital sander.

I was once a cabinet maker in a factory for high end coaches. We used plexi mirrors a lot.
 
Here's the post where I explained this thing.

https://www.truckersforum.net/forum/threads/duck-pond-redneckery.86547/page-39#post-561271

Here's those translucent light panels I'm talking about. Pic taken before I did the ceiling.

20161024_151308-jpg.36909


Illustration of what I mean by setting the plexiglass into table saw kerfs .

windows-jpg.36913


Except there will be two panes, not three.

Plans have a tendency to change on the fly when you're at Menard's looking at price tags. :toothpick:

But since this thing will be entirely inside the barn there's no need to use hardwood, pressure treated, or wood sealer. The plexiglass also won't have much air pressure on them either, if I seal up the translucent outer panels on the wall to serve as a third window pane.
 
Oh, and Menard's most likely has a cutting table. Most of the home improvement places here do. They can cut your plexi to whatever measurements you want in a lot less time than you can. And if they break it or cut it wrong, they eat the cost instead of you.
That is what I did when my Mom had her hip surgery and @Duck suggested putting cut fence posts under the coach legs to make it higher.
I got The Home De-pot to cut it for me. Big city apartment living does not lend itself to workshop activities
 
Some people use bubble wrap to insulate greenhouses.
I haven't tried it a lot of the youtubers claim it last for years.
One guy was growing orchids year-round and only using a very small heater to keep his greenhouse 60 or above.
I don't remember where he lived but there was snow on the ground.
 

Back
Top