Duck Pond Redneckery


1023125768-funny-cats-top-35-most-funniest-cat-quotes-26-778x1024-jpg.36799
:D
How would you know? :confused-96:
 
I went to the fire department today and talked to the chief.

Good guy.

I went there to ask if he had any info on building materials or could explain a whole bunch of acronym crap on the fire ratings and stuff on some materials I am considering covering the polystyrene with.

He said 5/8" dry wall. If not that, consult an architect, basically.

Said definitely do NOT have exposed polystyrene because it's made of oil and goes up quick. Says it also melts & drips as it burns and on the ceiling it would be like getting bombed with napalm and you wouldn't be able to find your way out because it makes tons of black smoke too. :eek:

So,.. No insulation at all on the workshop side of the rack wall. We can put it over the plywood on the unheated side later,since sparks from welding and cutting are the only things that would be a fire risk & there will be no welding and stuff going on in the cold side.


For the ceiling, our plan was to make a drop ceiling framed in 1x4's using 4'x8' sheets of 3" R-17 extruded polystyrene sheets with the foil reflective stuff on one side.

Fire chief says if I have a car in the workshop, just a simple little engine fire that I can quickly put out with an extinguisher can cause temperatures at the ceiling hot enough for that polystyrene to burst into flames even if actual flames don't reach within 6 feet of it. :stare1:

So,... store bought drop ceiling.

Geezer & I were at Menard's to get ten sheets of plywood. Looked at the drop ceiling stuff. It's fire rated to like 800 degrees.

840 ft², math works out to roughly $500.

Paperless fiberglass mats, ten inches thick, R-30 would be $250.

Didnt get any of that stuff but that's the plan now. Probably put this bubble stuff atop the fiberglass.

It's plastic but it'll be above the drop ceiling & insulation. Won't be a fire hazard cuz by the time flame or intense heat reaches it, the building is f***ed anyway.

Aluminized polyester? Bubble wrap. Stops 94% of Radiant heat.

My phone capitalizes Radiant because of Mike's old truck. :rolllaugh:

This stuff is definitely worth some research though. @Blood

20161018_192615.webp

2.webp

3.webp

It's just bubble wrap but has some impressive R values depending on how it's installed.

With a 1-¾" air gap on both sides it's got the same R value as 2" polystyrene.

$43 something for 100 ft². 4' x 25'.

On the innernet you can get a 100 ft roll for like $70 something though.

It's really light too. I pretended it was heavy and said "man this stuff uses some heavy foil like sheet metal or something" and handed it to my dad. When he grabbed it, he hit himself in the chin with it because he was preparing for it to be heavy. I could have thrown it at a big living room window without breaking it. It weighs nothing. Like I said it's just bubble wrap. Except it's shiny.

I'm thinking if it can be put up in the ceiling of a truck cab, it'll reduce the need for HVAC. Extend your non-idling season. It would be ugly as **** though.

Unroll it on top of the insulation in your attic, reduce air conditioning costs.

Because it's thin & lightweight, sew it between two bedsheets or blankets and make a super insulated (but noisy) blanket for sleeping in the truck in the winter months without a heater. Like if you've got an exhaust leak and no Airtronic heater. :toothpick:

There's lots of applications for it methinks.

Hell if you own a Husky or a Malamute, put it in the attic of it's dog house to help it stay cool in the summer. :)
 
Last edited by a moderator:
How in the hell would I secure ten of these to an 8x6 trailer behind my car?

Cigarette pack on it for scale.

20161018_192815.webp

It's on sale for half price until Nov 1. Gotta get it in the next 2 weeks.


It's roughly 4' x 2' x 2' and soft like pillows.

I'm thinking stack them so the long side is parallel to the axle, then pull two long ratchet straps over them, with the soft type bungee cords between the hooks and the trailer at one end. They won't be tight but the bungee will keep the straps taut enough the hooks won't come loose.

Then cover the stack with a cheap plastic tarp about 8x6 & use the same soft bungees (not rubber tarp straps) in every single eyelet, creating like a net over the top.

???

Only gotta go 13 miles.
 
Are you serious? Just stack them up and crank down on some straps. Or DUH, make 2 trips!
Multiple trips is absolutely out of the question. You should know that. I don't even do that when I'm carrying groceries into the house from the car.

Or "cah" as you'd pronounce it. :D

I don't wanta rip the plastic off by having the straps too tight and end up with that stuff blowing all over the road.
 
I don't wanta rip the plastic off by having the straps too tight and end up with that stuff blowing all over the road.

You hardly have to tighten them. Just a little and their not going anywhere!!! Some things I've hauled on the flatbed I could have tightened them so much I could compress a 12" thick bag into 1". There's no need. Once the middle is compressed just a little it's not going anywhere.
 
I went to the fire department today and talked to the chief.

Good guy.

I went there to ask if he had any info on building materials or could explain a whole bunch of acronym crap on the fire ratings and stuff on some materials I am considering covering the polystyrene with.

He said 5/8" dry wall. If not that, consult an architect, basically.

Said definitely do NOT have exposed polystyrene because it's made of oil and goes up quick. Says it also melts & drips as it burns and on the ceiling it would be like getting bombed with napalm and you wouldn't be able to find your way out because it makes tons of black smoke too. :eek:

So,.. No insulation at all on the workshop side of the rack wall. We can put it over the plywood on the unheated side later,since sparks from welding and cutting are the only things that would be a fire risk & there will be no welding and stuff going on in the cold side.


For the ceiling, our plan was to make a drop ceiling framed in 1x4's using 4'x8' sheets of 3" R-17 extruded polystyrene sheets with the foil reflective stuff on one side.

Fire chief says if I have a car in the workshop, just a simple little engine fire that I can quickly put out with an extinguisher can cause temperatures at the ceiling hot enough for that polystyrene to burst into flames even if actual flames don't reach within 6 feet of it. :stare1:

So,... store bought drop ceiling.

Geezer & I were at Menard's to get ten sheets of plywood. Looked at the drop ceiling stuff. It's fire rated to like 800 degrees.

840 ft², math works out to roughly $500.

Paperless fiberglass mats, ten inches thick, R-30 would be $250.

Didnt get any of that stuff but that's the plan now. Probably put this bubble stuff atop the fiberglass.

It's plastic but it'll be above the drop ceiling & insulation. Won't be a fire hazard cuz by the time flame or intense heat reaches it, the building is f***ed anyway.

Aluminized polyester? Bubble wrap. Stops 94% of Radiant heat.

My phone capitalizes Radiant because of Mike's old truck. :rolllaugh:

This stuff is definitely worth some research though. @Blood

View attachment 36805

View attachment 36806

View attachment 36807

It's just bubble wrap but has some impressive R values depending on how it's installed.

With a 1-¾" air gap on both sides it's got the same R value as 2" polystyrene.

$43 something for 100 ft². 4' x 25'.

On the innernet you can get a 100 ft roll for like $70 something though.

It's really light too. I pretended it was heavy and said "man this stuff uses some heavy foil like sheet metal or something" and handed it to my dad. When he grabbed it, he hit himself in the chin with it because he was preparing for it to be heavy. I could have thrown it at a big living room window without breaking it. It weighs nothing. Like I said it's just bubble wrap. Except it's shiny.

I'm thinking if it can be put up in the ceiling of a truck cab, it'll reduce the need for HVAC. Extend your non-idling season. It would be ugly as **** though.

Unroll it on top of the insulation in your attic, reduce air conditioning costs.

Because it's thin & lightweight, sew it between two bedsheets or blankets and make a super insulated (but noisy) blanket for sleeping in the truck in the winter months without a heater. Like if you've got an exhaust leak and no Airtronic heater. :toothpick:

There's lots of applications for it methinks.

Hell if you own a Husky or a Malamute, put it in the attic of it's dog house to help it stay cool in the summer. :)


Been using bubble wrap on the windows in the winter time since coming to Tennessee. Works great, come spring just roll up and store until next winter. When we did it the first year temp one foot inside window in a heated room was 53 deg, with bubble wrap on the window it was 68 deg matching the room.
 
I made a miter saw table, and dissected my grandpa's rusted up planer & got it working today.

Most productive day I've had in... :headscratch2:... since yesterday. ;)

20161019_180142.webp

The vertical shafts at the 4 corners, and the auger crank thingy on the right side were rusted & seized. Wouldn't crank up & down. All cleaned up now. Works good. :thumbsup:

Needed to use it to mill some wood down to exact thicknesses for the miter saw table so they add up to the same height as the saw.

20161019_192317.webp

And I also discovered that you can literally run a circular saw blade sideways in wood if the blade depth is shallow enough. I figured it out when I was doing this:

20161019_161940.webp
 
For this joint:

20161019_163516.webp

Because I didn't have a 2x12 but I had a couple of 2x6's. ;)

Oh and when notching this piece to fit over a joint on the pallet rack.

Cutting 3/16" or shallower in wood you can literally push the saw sideways. I was like "Holy crap!"

20161019_194516.webp
 
I made a miter saw table, and dissected my grandpa's rusted up planer & got it working today.

i got rid of my dad's joiner/planer, lathe, and table saw and scroll saw.

as well as the tools, and the portable T stand for the lathe.

just gave'em away to a buddy and his son.

could care less what they did with any of it.

i got my own router, table saw, and mitre saw, as well as drills, and other crap, and i hardly ever use my crap, let alone dad's crap.

but dad's crap, just one of anything i gave away, weighs more all my crap put together....

i think dad's crap could be melted down for an anchor for a battleship.
 
i got rid of my dad's joiner/planer, lathe, and table saw and scroll saw.

as well as the tools, and the portable T stand for the lathe.

just gave'em away to a buddy and his son.

could care less what they did with any of it.

i got my own router, table saw, and mitre saw, as well as drills, and other crap, and i hardly ever use my crap, let alone dad's crap.

but dad's crap, just one of anything i gave away, weighs more all my crap put together....

i think dad's crap could be melted down for an anchor for a battleship.
Your dad's crap was probably QUALITY MADE IN USA stuff with actual BEARINGS and STEEL parts. Your "lightweight" crap is Chinese and it's only lightweight because it's made of PLASTIC.

You should've given away your own crap and kept your dad's.
 

Back
Top