EC's Going For It


First full day with the new sensor pigtail. Seems A-OK. I guess it's a good fix so far.

I was enjoying trucking again for the first 2 out of 3 legs of my day today. The load going down was about 36k and it rode nice and pulled nice and was pretty straight giving me good mileage for the weight.

Second leg was an empty to Richmond and besides being empty it too was straight as an arrow.

Get my load from Richmond and that thing is a cattywompus POS. Not the worst I've pulled but when you go two in a row straight anything less seems even worse. So annoying.
 
Original plan was to run a load down to the regular in Virginia then bring an empty back then that was it. I wanted to leave around 6am. But CSX never took my box off the train and I finally got leaving 3 hours later to do a pair of pickups out of Hanover PA. It's a time sink when there aren't any direct interstates to take and it's all local roads. Especially being just 50 miles each way. It's like wtf where is my time going. lol.

Nice change of pace though, just got back later than expected.

I took the pickup to run some errands. It ran great until I got a couple miles from home then it stumbled and shut off like last time when my dad pushed me. The new starter let me crank the shit out of it and get it to fire good enough to get back, and it ran pretty smooth then started easy again after I got home and shut it off and started it back up.

I don't know if this thing needs a new injection pump or its letting debris pass through the filters or what. It's set up kind of like a semi with a water separator on the firewall (like a Davco almost) then the secondary spin on filter near the pump. I could try replacing both filters again but I doubt that's it. It runs smooth as butter when it runs but then it just stumbles and cuts off out of nowhere.
 
Original plan was to run a load down to the regular in Virginia then bring an empty back then that was it. I wanted to leave around 6am. But CSX never took my box off the train and I finally got leaving 3 hours later to do a pair of pickups out of Hanover PA. It's a time sink when there aren't any direct interstates to take and it's all local roads. Especially being just 50 miles each way. It's like wtf where is my time going. lol.

Nice change of pace though, just got back later than expected.

I took the pickup to run some errands. It ran great until I got a couple miles from home then it stumbled and shut off like last time when my dad pushed me. The new starter let me crank the shit out of it and get it to fire good enough to get back, and it ran pretty smooth then started easy again after I got home and shut it off and started it back up.

I don't know if this thing needs a new injection pump or its letting debris pass through the filters or what. It's set up kind of like a semi with a water separator on the firewall (like a Davco almost) then the secondary spin on filter near the pump. I could try replacing both filters again but I doubt that's it. It runs smooth as butter when it runs but then it just stumbles and cuts off out of nowhere.
Sounds like water. Especially as cold as it’s been?
 
Cub Cadet. That's like top of the line right?
The only Cub Cadet products that'll be "top of the line" or near the top of the line, would be the ones that you'd find at an actual Cub Cadet dealer.

Same goes for John Deere and all the other brands with historically good reputations.

The problem is the big box stores. Cub Cadet, John Deere, etc allow their names to be put on inferior Chinese made products to be sold at the big box stores.

And get this - they even use some of the same model numbers as the quality built American versions that cost twice as much.


So it's a nightmare ordering parts. Especially when you don't know it's a Chinese knockoff.
 
Last edited:
I got my zero turn at Tractor Supply and my snowblower at Home Depot. Neither was particularly expensive but neither was cheap either. I think I gave about $1500 for the snowblower and $3500 for the mower. I got a 4 stroke (gas and oil separate) Cub trimmer and I think that was also Home Depot. It was pretty salty compared to a common 2 stroke.

At the time I didn't have anything else that was a 2 stroke so I didn't want to keep a mix just for it. Especially since I knew I'd barely use it.

According to Wikipedia, Cub Cadet was bought by MTD from International Harvester in 1981. In 2021 Stanley Black & Decker took complete ownership of the brand. MTD has a bunch of different brands. Most of them are the cheap box store mowers.
 
Y'all were right. I thought the bowl was empty but it was so full it looked empty. I thought I had a spare to change it out but it's the wrong threads. For now I dumped out the bowl and reinstalled the filter, and put 2 of the correct ones on order. Should be here Friday.

Don't know if that ultimately solves it but it's definitely gonna help.
 
Longer day today. Put about 11 hours in altogether. Not as lucrative as it was in the olden days but the sleeper truck is turning a better profit than the day cab did and my quality of life is vastly improved in ride and having the fridge and microwave.

The old me would try to hustle every stop to 30 minutes if I needed to reset my 8 or less if I didn't need to.

Now I'm like "it's been 40 minutes? Cool. Whatever. This Salisbury steak is delicious."

Today was also crawling most of the way back from Upper Marlboro MD (301 east of DC) and I hit it smack in the middle of rush hour. Didn't really even care about that either. Millions of other people were stuck in it with me after all.

I hadn't been there in ages and the girl working the shipping desk recognized and remembered me. That was kind of nice.
 

Back
Top