Duck Pond Redneckery


I replaced one ignition coil on my Jeep a few weeks ago. One electrical connection and one 10mm nut. Took me 4 hours! Never again!
So how much crap did you have to take off to get to it?

Yeah I won't work on cars built after 1990 unless it's something simple like replacing a battery or a serpentine belt.

Speaking of that,....

I was able to order a "maintenance free" battery dry and put the electrolyte in it myself.

And give it a slow initial charge.

20170203_012729.webp

(It's a side post battery but I have conversion posts I keep in my toolbox just for charging them when they're new.)

It's literally the cheapest battery they had.

But it's bullshit that they sell batteries with the acid in them already, and they sit on a shelf for months in a 50% state of charge.

When you put the electrolyte stuff in them, they immediately have a partial charge in them. Enough to start a car, then fast-charge off the alternator. That's horrible for a battery. They fill them up with electrolyte and ship them that way to most retailers.

Only a few places order them dry. There's an interstate batteries place in Key Kanker Town but they charge like 6 trillion for a battery and they fill their whole shipments upon delivery so they still set on their shelves with a partial charge in them. :mad:



Best automotive batteries I've ever had were the YUASA that came in my Honda ATV, lasted ten years. And the original Delco battery that came in my Buick which lasted 13 years.
 
It's why I didn't take & mud those two little scraps above the heater in the barn.

I was just thinking about the phrase 'take and' the other day.
As a kid I knew several people who used that every few sentences but I haven't heard anyone say that in a long time.
'Haul off' is another one.

Not relevant to anything...
I just thought I'd take and haul off and write a post about it before someone else took and hauled off and wrote a post about it.
That would have pissed me off, then I'd have to take and haul off and give somebody a cussing.
;)
 
I was just thinking about the phrase 'take and' the other day.
As a kid I knew several people who used that every few sentences but I haven't heard anyone say that in a long time.
'Haul off' is another one.

Not relevant to anything...
I just thought I'd take and haul off and write a post about it before someone else took and hauled off and wrote a post about it.
That would have pissed me off, then I'd have to take and haul off and give somebody a cussing.
;)
That was an autocorrect failure.

Tapeworm and music.

:mad:

Tape and mud.
 
some may recall that at one time I had thought about buying a battery conditioning business i Texas, during my research I learned a lot of facts about how to maintain batteries that over the years saved me a lot of money, in the end I didn't buy the business but did buy a single station battery re conditioner and a GOOD battery tester at a good price on e-bay.
the first thing is never let a battery fall below 10% of a full charge, it begins to sulfide the plates the if you do and to drain one dead will cut a year or more off its life.
next keep the top and posts CLEAN dielectric grease should be used on the terminals.
batteries that are stored should always be hooked up to a small automatic charger, think motorcycles and boats.
tired of the high price of new batteries? with what I have I made a deal with a small shop that lets me go thru their batteries that are destined for the recycle pile and you would be surprised at how many are actually good but need a month on the reconditioning machine for a month or so that thing has payed for itself time and time again.
batteries with lower amperage have thicker plates thus will last longer.
I have a battery in my pickup that I started experimenting with it is going on 10 yrs old,granted it is starting to lose storage capacity but unless I let it sit for a few weeks it still starts the truck just fine even in the cold 17 here this morning.
also remember a dead battery should be charged instead of jumped alternators are really meant to maintain a charge not charge a dead battery
 
some may recall that at one time I had thought about buying a battery conditioning business i Texas, during my research I learned a lot of facts about how to maintain batteries that over the years saved me a lot of money, in the end I didn't buy the business but did buy a single station battery re conditioner and a GOOD battery tester at a good price on e-bay.
the first thing is never let a battery fall below 10% of a full charge, it begins to sulfide the plates the if you do and to drain one dead will cut a year or more off its life.
next keep the top and posts CLEAN dielectric grease should be used on the terminals.
batteries that are stored should always be hooked up to a small automatic charger, think motorcycles and boats.
tired of the high price of new batteries? with what I have I made a deal with a small shop that lets me go thru their batteries that are destined for the recycle pile and you would be surprised at how many are actually good but need a month on the reconditioning machine for a month or so that thing has payed for itself time and time again.
batteries with lower amperage have thicker plates thus will last longer.
I have a battery in my pickup that I started experimenting with it is going on 10 yrs old,granted it is starting to lose storage capacity but unless I let it sit for a few weeks it still starts the truck just fine even in the cold 17 here this morning.
also remember a dead battery should be charged instead of jumped alternators are really meant to maintain a charge not charge a dead battery
The battery currently in my Buick was dead last winter.

Dead as in, interior light wouldn't even come on and after being on an automatic charger for a WEEK all it did was click the solenoid.

Then in the summer I turned the key just for the hell of it and it started. :confused:

Worked fine all summer and in fact I can probably go start it now. I even made a trip to Tennessee with it.

I drove it to Wilmington and back last week though, and at every red light my lights dimmed and I turned off the heater fan to protect the alternator from overload.

I don't want to fry my alternator so that's what the new battery is for.

And since that junk battery in it now is still capable of starting the car, I'm going to put it in the workshop to power my raft stereo. I shouldn't be short-cycling my deep cycle marine batteries when thin plate car batteries are actually designed for that.


I'd like to learn how to desulfate a battery though. It's something about dumping huge amps and high voltage into it for a while. It's more complicated than that. I read up on it once but don't remember it.
 
the re conditioners at least the one I have pulses the voltage at a rapid rate which by my understanding causes the sulfide to flake off over time cleaning the plates.
the only thing that will kill a properly maintained battery in theory is either shorting out of the plates due to the buildup of sulfide in the bottom or flat out wearing out the plates themselves.
The pickup battery I was speaking of I actually drained of acid and in a parts washer turned it upside down and flushed the sulfide out of it had to go buy a vibrator and used to loosen the crud off the bottom but it worked and I was amazed at all the goo that was in it.
when I use the battery up to where it will not start the truck anymore I plan on tearing it apart and see just how much of the plates are left.
I have heard of people hooking up welder to batteries to clean them and also hear of people blowing them up that way so if you experiment do it safely
 
I read that you could reverse the polarity of a dead battery sometimes by hooking a charger up backwards. It's also suppose to desulfate the plates.
I tried it and it actually did work...
to a point.
The battery held a shallow charge and wasn't fit to use but it did change the polarity and took some charge where it wouldn't take any charge at all before.
 
A couple weeks ago when I was trying to start the (6 volt) tractor out in the cold, it wasn't cranking fast enough to start until I turned the booster up to "12 volt high / boost".

It's allegedly 18 volts, 200 amps.

The gauge on the booster said it was accepting about 40 amps.

I could hear bubbling or boiling coming from the battery and after a few minutes I saw smoke.

The smoke was grease burning off of the positive clamp. o_O

I don't care. I'm converting that thing to 12 volts. I'll probably strip open that old 6 volt battery and save the posts and plates. That's what I do with old batteries.

Tree huggers shut down lead smelting in the USA, which made the lead in a car battery more valuable than the core charge.

Unless it's a lawnmower or motorcycle battery. Same core charge, and the core doesn't have to be the same as the one you buy.
 
I've got a whole pallet full of truck batteries.
I should load a car and and those batteries and make a run to my cousins scrap yard...
instead of sitting on my ass reading drivel.
;)
 
I've got a whole pallet full of truck batteries.
I should load a car and and those batteries and make a run to my cousins scrap yard...
instead of sitting on my ass reading drivel.
;)
then stand up dammit man, stand up..drivel rolls down easier with no resistance this way.
 
I was just thinking about the phrase 'take and' the other day.
As a kid I knew several people who used that every few sentences but I haven't heard anyone say that in a long time.
'Haul off' is another one.

Not relevant to anything...
I just thought I'd take and haul off and write a post about it before someone else took and hauled off and wrote a post about it.
That would have pissed me off, then I'd have to take and haul off and give somebody a cussing.
;)
"Boy, you'd best straighten up or I'm gonna haul off and smack the shit out of you!"

I do believe I've heard that a time or two.


Not directed at me, or anything... but I heard it!
 
I replaced one ignition coil on my Jeep a few weeks ago. One electrical connection and one 10mm nut. Took me 4 hours! Never again!
I changed out the heater fan in an EX GFs car, It took me the whole damned day! Anyone here will tell you it would be about an hours work.
I had my beer and I just had to get out of the damned house. I was a hero to her and I kept my sanity....for that day:D
 
I changed out the heater fan in an EX GFs car, It took me the whole damned day! Anyone here will tell you it would be about an hours work.
I had my beer and I just had to get out of the damned house. I was a hero to her and I kept my sanity....for that day:D
some day, try and remove and replace a heater core in these cars, and even light pick up trucks..

you had better have at the very least...15 - 20 hours of spare time. that's for a home mechanic. shops try and get it done per book time of 11 hours.
 
A couple weeks ago when I was trying to start the (6 volt) tractor out in the cold, it wasn't cranking fast enough to start until I turned the booster up to "12 volt high / boost".

It's allegedly 18 volts, 200 amps.

The gauge on the booster said it was accepting about 40 amps.

I could hear bubbling or boiling coming from the battery and after a few minutes I saw smoke.

The smoke was grease burning off of the positive clamp.

I don't care. I'm converting that thing to 12 volts. I'll probably strip open that old 6 volt battery and save the posts and plates. That's what I do with old batteries.

Tree huggers shut down lead smelting in the USA, which made the lead in a car battery more valuable than the core charge.

Unless it's a lawnmower or motorcycle battery. Same core charge, and the core doesn't have to be the same as the one you buy.[/QUOTE


used to make a hundred bucks a pop converting old fords to 12 volt all you need is a self exciting alternator and the thingy that reduces the voltage down to 6 volts for the lights if any and a hour of time put my # out at the farm store and the farmer ringing my phone off the wall that was in the mid 70's
 
some day, try and remove and replace a heater core in these cars, and even light pick up trucks..

you had better have at the very least...15 - 20 hours of spare time. that's for a home mechanic. shops try and get it done per book time of 11 hours.
My days of working on cars ended when everything became a sensor. The only thing I do on my own now is change the air filter.
I will be damned if I am going to pay the parts mark up and labor on that:D
 
My days of working on cars ended when everything became a sensor. The only thing I do on my own now is change the air filter.
I will be damned if I am going to pay the parts mark up and labor on that:D

Parts stores around here will change it for you.
Same with lights, wipers, etc...
but they'll probably call you mam if you ask them.

I send my wife.
:D
 
I changed out the heater fan in an EX GFs car, It took me the whole damned day! Anyone here will tell you it would be about an hours work.
Except me. ;)

used to make a hundred bucks a pop converting old fords to 12 volt all you need is a self exciting alternator and the thingy that reduces the voltage down to 6 volts for the lights if any and a hour of time put my # out at the farm store and the farmer ringing my phone off the wall that was in the mid 70's
Wire the lights in series.
 
Thinking I'm gonna run the air in 3/8" copper with flare fittings from the tank down into the closet below, then switch to threaded brass and rubber hose.

The flexible copper, not rigid.


Black pipe rusts and clogs air tools. Galvanized pipe flakes and clogs air tools.
PVC and PEX isn't really made for 155 psi and is degraded by compressor oil. When it fails in that application, it shatters and chunks of plastic become shrapnel. It's an OSHA violation in commercial or industrial applications.

Aluminum, I don't even know where to get.



I haven't flared tubing in probably 20 years, and it was brake line stuff.

Well I got bored and flared a scrap of half inch copper not too long ago but I didn't use it in a connection.

I don't trust compression fittings. I could solder it but then I'd have to thread copper NPT into brass. Not sure how tight I'd be able to crank that.
 

Back
Top