Duck Pond Redneckery


I couldn't find a barbed fitting for 1/2" hose at Menard's with glue joint or pipe thread fittings. So the jury was still out on how I was going to connect the furnace drain to PVC for a proper drain instead of the flexible hose zip tied to the electrical conduit.

I just discovered this. That's the scrap piece I was going to bring with me to a plumbing supply place, and a garden hose end. :D

20170129_232638.webp

That's when I dug through my plumbing crap and found this:

20170129_234145.webp

Garden hose threads on one side, half inch MPT on the other. I just gotta find a PVC fitting with a glue joint socket on one side and FPT on the other.

No idea if you can do that in house sink drain stuff. Brass threaded into PVC I mean.

Also no idea if I'll need to use teflon tape or how tight to crank it.

But I'll figure it out. :thumbsup:
 
Crank it hand tight when using PVC. Anything more and you'll strip it. And yes, plumbing tape or that brush-on goo.
Yeah it just has to not leak at zero psi.

I'm loving the fact that I will have a garden hose fitting there instead of a barbed fitting. Because black stuff builds up in the trap and I'll have to dump it out periodically. And maybe use the compressor to blow out the PVC if it builds up in there too.

I have no idea what that black stuff is but I'm thinking the propane guys lied to me when they said they did that gas pressure test. That thing with the manometer. I noticed a lot of orange in the flame the other day. I'm thinking the regulator outlet /burner inlet pressure is too high and it's creating soot?


As for the threads, they're not going to strip out. It's male brass, female plastic. It won't strip. It'll simply split open the plastic part. My plan was to get two of them and purposely overtighten and break the first one so I can get an idea how much torque it can take. They're like 50 cents.
 
Yeah it just has to not leak at zero psi.
As for the threads, they're not going to strip out. It's male brass, female plastic. It won't strip. It'll simply split open the plastic part. My plan was to get two of them and purposely overtighten and break the first one so I can get an idea how much torque it can take. They're like 50 cents.
reminds me of a neighbor of mine he was one of them know it all types
He was trying to put an old tractor together is seamed that every 20 minutes he was calling he asking me how to do something and telling me how that the last thing I told him how to do he had found a better way.
well we got to the head and borrowing my valve spring compressor and bringing it back and proudly showing me how he had "modified" it by grinding the ears down he then ask me how to torque the head bolts and VAGUELY explaining to him he had the gall to ask to use my torque wrench you can guess my answer, he tried to borrow one from several other people without luck and called me late at night "I was asleep" he wanted to know how to do it without a torque wrench so I told him to torque them down 2 turns after they snap and back off a half a turn and back off a half turn.
haven't talked to him since.
interestingly enough I had a similar experience with a jerk in high school and have never heard from him either
 
reminds me of a neighbor of mine he was one of them know it all types
He was trying to put an old tractor together is seamed that every 20 minutes he was calling he asking me how to do something and telling me how that the last thing I told him how to do he had found a better way.
well we got to the head and borrowing my valve spring compressor and bringing it back and proudly showing me how he had "modified" it by grinding the ears down he then ask me how to torque the head bolts and VAGUELY explaining to him he had the gall to ask to use my torque wrench you can guess my answer, he tried to borrow one from several other people without luck and called me late at night "I was asleep" he wanted to know how to do it without a torque wrench so I told him to torque them down 2 turns after they snap and back off a half a turn and back off a half turn.
haven't talked to him since.
interestingly enough I had a similar experience with a jerk in high school and have never heard from him either
I carried a Snap-On torque wrench in my truck for 3 years hoping to catch the guy who fleeces the mechanics at the shop.

It was my uncle Dave's. He died in 1987 and my dad and grandpa split his tool collection. That torque wrench only works in reverse. (Polish threads or removing a fastener). Clockwise the needle stops at 5 lbs no matter how hard you crank on it.

I never did catch the Snap-On guy to take advantage of the lifetime warranty and I still have it. :mad:

And because I (on my dad's behalf) can theoretically get it replaced for free if I can find one of those guys, I've never bought one for myself. Though I did borrow one once when I rebuilt the engine on my VW Beetle a million years ago.
 
I carried a Snap-On torque wrench in my truck for 3 years hoping to catch the guy who fleeces the mechanics at the shop.

It was my uncle Dave's. He died in 1987 and my dad and grandpa split his tool collection. That torque wrench only works in reverse. (Polish threads or removing a fastener). Clockwise the needle stops at 5 lbs no matter how hard you crank on it.

I never did catch the Snap-On guy to take advantage of the lifetime warranty and I still have it. :mad:

And because I (on my dad's behalf) can theoretically get it replaced for free if I can find one of those guys, I've never bought one for myself. Though I did borrow one once when I rebuilt the engine on my VW Beetle a million years ago.
i never had a snap-on torque wrench fail me,. if i recall, they do not replace torque wrenches, they send it out for repairs and recalibration. i also have good luck with sears torque wrenches, for the few times i needed them, and still have all my torque wrenches
 
Can't do nothing in the barn til the propane truck shows up. :mad:

Them bastards said they operate their service like there's a pipeline... Meaning they have "algorithms" for predicting when everyone is getting low and they send out the trucks ahead of time and nobody ever runs out.

But then they told me this would happen cuz we added the workshop heater. I said how about adjusting your "algorithm" now? He said "blah blah blah blah blah" that translates to "I don't know I just work here".. :rolleyes:

Well I left the light on for 'em.

I shoulda told them to bring Jimmy John's. :order:
 
Them dumbasses brought out a BBQ grill tank and hooked it up.

:bonk:

I'm not kidding.

For some reason their tanker trucks in the daylight. I guess they're solar powered. :dunno:

But I can't heat the workshop til they fill the real tank tomorrow. :mad:
 
Them dumbasses brought out a BBQ grill tank and hooked it up.

:bonk:

I'm not kidding.

For some reason their tanker trucks in the daylight. I guess they're solar powered. :dunno:

But I can't heat the workshop til they fill the real tank tomorrow. :mad:
sure you could heat the barn up get a 55 gallon drum and light a fire in it:D
 
You don't think it's because it's going to cost a fortune to heat that garage?
The tank hasn't been topped off since before the heater was hooked up. It was at 40% at the time. (40% of what, I don't know.)

When the heater was hooked up it was costing approximately $25 a day to heat it with kerosene.

Only 8 feet of wall was insulated at the time.
There's 120 feet of wall altogether.

That's about 1500 square feet of thin steel with freezing cold air and wind on the other side.

You know how long that took me to insulate and wall up. ;)



Heater kept it 68° while I was in there, 50 at night.

For months...

The house was built in 1915, is poorly insulated and has cheap leaky windows. It's kept at 69° 24/7.

The tank ran empty simply because the additional consumption wasn't monitored.

So stuff it, commie. :toothpick:
 
At 8:04 pm last night I made that post saying out of propane.

Temp in here was 53° at the time.

It's been ten hours.

Weatherbug says it's 36 outside, wind chill 30. It's really windy. I just parked my Ranger in the yard to provide a wind break for the garbage cans. It's that windy.

Anyway I left the outdoor light on last night so I cane in here to shut it off, and check the temp cuz I'm curious....

It's 47°.

In ten hours it has lost 6 degrees. And that's with the ceiling fan off.

20170131_060703.webp

20170131_061301.webp

The analog thermometer is on the wall about 9 feet up. The digital thermostat is 5 feet up.


Yeah, it's going to cost millions to heat this shop.

:coocoo:



Of course,.... I suppose high mass objects do help a little:

20170131_061605.webp
 
The tank hasn't been topped off since before the heater was hooked up. It was at 40% at the time. (40% of what, I don't know.)

When the heater was hooked up it was costing approximately $25 a day to heat it with kerosene.

Only 8 feet of wall was insulated at the time.
There's 120 feet of wall altogether.

That's about 1500 square feet of thin steel with freezing cold air and wind on the other side.

You know how long that took me to insulate and wall up. ;)



Heater kept it 68° while I was in there, 50 at night.

For months...

The house was built in 1915, is poorly insulated and has cheap leaky windows. It's kept at 69° 24/7.

The tank ran empty simply because the additional consumption wasn't monitored.

So stuff it, commie. :toothpick:
that's still what, nearly $750 for the month..??? $25 x's 30 (days)

that's a lot of money for heating.

my electric bill is roughly $200 per month, mom and sis's gas bill is roughly $250 per month for heating.
 
@Duck s tank is 500 gallons.
40% = 200 gallons.
According to Google current price in Illinois is 1.65 So that's $330 since he checked it at 40%.

In Missouri I paid 1.04 in the fall and topped off a week or two ago at 1.36....
 
I got the LPG price for Duck in Illinois from eia.gov
I just checked Missouri and it says 1.60 so Duck may be paying less than I estimated...
I naturally assumed that the price in Illinois would be higher due to taxes out the ass.
 

Back
Top