Duck Pond Redneckery


If your thermostat will hold the program on a separate circuit or battery power the simplest solution that I know would be a simple farmers add-on outlet that powers on at just above freezing and powers off around 40 degrees.

Just run your thermostat 'always on' and plug the heater into the freeze protect outlet.
10 bucks at that farm store down the road...
K.I.S.S.

LINK
I don't know if that will work. When the AC power is turned off, because of some stupid computer crap, it won't turn on unless the thermostat is turned on AFTER the AC power is restored. If the thermostat is telling it to fire up when the power comes back on, it goes into some stupid safety mode. It's stupid.
I think that's the old school way. It's called a bimetalic coil. Same as an old car used to set the choke in a carb. In my day the contact was made with a little like light bulb filled with mercury. When it tipped over it made contact with 2 wires.
If it's a coil, it's not bi-metallic. Doesn't need to be, anyway. All it has to do is expand in length and it'll rotate itself. The inside is held still, so as it lengthens, the outer end rotates around the axis.

A bi-metallic strip is used in some thermostats but probably aren't very accurate. They're in old school mechanical turn signal flashers.

And I think the mercury tilt switches are banned or something.
 
I think mercury is something that's absorbed through the skin. Can't remember. Can kill you pretty quick if you get it inside you
 
I don't know if that will work. When the AC power is turned off, because of some stupid computer crap, it won't turn on unless the thermostat is turned on AFTER the AC power is restored. If the thermostat is telling it to fire up when the power comes back on, it goes into some stupid safety mode. It's stupid.

The Honeywell smart thermostat we installed with the high efficiency furnace a couple of years ago has a programmable emergency setting.
It will make 3 or 4 attempts at the primary source before switching over to run propane each time the setting fails.
Not ideal but it might work.
I think we only paid around 50 bucks for it but I'm pretty sure my HVAC guy got a deal.
I can post the model # later on if you want.
 
Did you know that Steve Millers parents lived next door to Les Paul & Mary Ford.
Steve Millers first encouragement except from his parents was from Les Paul while Les n Mary were having cocktails with the Millers.

Little Stevie came out after he was suppose to be tucked in and tried to play a riff.
Les Paul told his parents not to discourage him because 'the kid might have some talent'.
:cool:

 
I'd like to have one that can be set anywhere from 25 to 80.

When I'm working in there, I keep it at 67. I'd only want the capability of 80 to warm up all the objects faster.




I'd like to make a greenhouse as a lean-to on the south side and rig up a simple thermostat to blow air in through the window, but have it automatically close the windows and turn off the fan at night. That way it's always somewhat warm in there during the day



The thing about thermal mass is when you're in there with the heat on, it's sucking heat out of the air. So the heat given off in the night isn't free energy at all. Unless it's heated with solar.



I'd like to build a big sand box.

Railroad ties, about 2 feet deep, maybe 10 x 10.

Fill it with a zigzag pattern of copper tubing and bury it in sand.

Level the sand perfectly flat and lay aluminum sheet metal on top of it.

Take an acetylene torch and light only the acetylene, no oxygen. Use it to coat the entire surface of the aluminum with soot. It's flat black. Absorbs heat.

Then cover that with polycarbonate, framed to hold it in a slightly upwards arch for strength against snow loading, squirrels and Rabbits running across it, etc. Spaced about a foot above the aluminum.

Sand is better than water at retaining heat.

Run water through the copper pipes in the sandbox and through a car radiator inside the building.
 
I'm surprised steel mills don't take advantage of all the heat they are just pissing away. Maybe new ones being built would but I don't think anyone builds a new mill. They just buy existing ones and add on.
 
Electronic temperature controllers are pretty simple suckers, and y'all don't need no stinkin' microprocessor ta do it.

If it's electronic, the temperature sensing element is based on the thermal characteristics of a reverse biased pn junction. A diode that's turned off - a 1N914 would do as well as anything. It has a nice linear voltage vs temperature characteristic. Hook that to whatever you're using for a controller, and voila!

Simplest and cheapest is an op-amp like an LM741 connected as a voltage comparator. Diode goes in the negative input, and a potentiometer for your temperature set point in the other. Use a Sharpie and a file card to set the temp points... 10° increments is close enough. Output runs an el-cheapo power transistor like a 2N3904... use that to run the relay that turns the heater on/off. Done. Maybe $5 total. Less if you have a well stocked junk box.

Which is pretty much what a technogeek is gonna do with a computer. And a whole buncha C gobbletygook code. And a digital display. And a plastic project box. And a power supply. We're talking $50 or so, depending on how fancy the digital display gets. Oh, and a penny for that diode.
 
Last edited:
I'm surprised steel mills don't take advantage of all the heat they are just pissing away. Maybe new ones being built would but I don't think anyone builds a new mill. They just buy existing ones and add on.
Run by Columbia City IN on US30 west of Ft Wayne sometime.

Steel Dynamics Inc.

Brand spankin' new steel mill built in the last 5 years.

https://www.google.com/url?sa=t&sou...XiszLVaTEgWkhto1w&sig2=c-hpjFhv6BYYvAK9ZYMTjg

Why new? Because it would cost 1000 times as much to renovate some old junk pile. It's probably a Superfund site anyway because of all the crap that just got dumped years ago, and a company that moves into that inherits the financial responsibility for someone else's mess.

This is where your technogeeks come in, because a new mill is going to be highly automated. Payroll costs slashed because of automation.

The Mexicans didn't take the jobs. The technogeeks and their soulless robots did.
 
Last edited:
Electronic temperature controllers are pretty simple suckers, and y'all don't need no stinkin' microprocessor ta do it.

If it's electronic, the temperature sensing element is based on the thermal characteristics of a reverse biased pn junction. A diode that's turned off - a 1N914 would do as well as anything. It has a nice linear voltage vs temperature characteristic. Hook that to whatever you're using for a controller, and voila!

Simplest and cheapest is an op-amp like an LM741 connected as a voltage comparator. Diode goes in the negative input, and a potentiometer for your temperature set point in the other. Use a Sharpie and a file card to set the temp points... 10° increments is close enough. Output runs an el-cheapo power transistor like a 2N3904... use that to run the relay that turns the heater on/off. Done. Maybe $5 total. Less if you have a well stocked junk box.

Which is pretty much what a technogeek is gonna do with a computer. And a whole buncha C gobbletygook code. And a digital display. And a plastic project box. And a power supply. We're talking $50 or so, depending on how fancy the digital display gets. Oh, and a penny for that diode.

13876119_1739145273025985_8111063057624872881_n.webp
 

Back
Top