Duck Pond Redneckery


First "official" fixin' job in the workshop, which ain't even done yet.

A really dumb guy is spending more money than it's worth to fix this mower after "his wife" hit something with it and bent the front of the deck into the blades.

Yeah. Blame it on the wife. :rolleyes:

But it's also rusted out badly so he ordered a new deck & had it shipped here. $200 for that plus $200 I'm charging him. And it needed a starter solenoid. He'd been starting it with a wrench across the terminals. Roughly $420.

He could've bought a comparable used mower for that, and turned this one into a racing toy for drunk people. :toothpick:

20160815_020205.webp

20160815_020142.webp

I sanded this down to bare metal cuz at first I was thinking I'd end up welding a patch over it.

20160815_021750.webp

But this is why you should clean the bottom of the mower deck frequently. Everything is made of super thin stuff these days. This mower is only 2 years old he said.
 
Your Great-GranPoppa build this, Duck?

6.jpg
 
Just got this boat for free.

20160815_140058.webp

The guy I worked for making elevator parts said his wife made him pick between the boat and the 6 seater plane he just bought.

20160815_140312.webp

Sell it? Nah.... He's too smart for that.. Give it to a friend who has a place to store it so you can borrow it whenever you want. ;)

Anyway I have no idea what it looks like under that cover. He didn't pull it off and I wasn't going to look a gift horse in the mouth.

He said it's a Ford 3 liter 4 cylinder?? :dunno:

2 liter Ford Probe engine I'm thinking based on he said it's a Ford, and the title says 1993 model year and 115 hp.

Only problem I know of at this point is it will draft too much to take it down my favorite part of the river.

The REASON I prefer that stretch between the state line and Momence is because it's too shallow for water cops. So it's anarchy, which actually works quite nicely for unregistered homemade things that look like a couple of mattresses tied together. They all use big V-bottom boats with big V8 engines.

The Geezer wants to drive it down the Illinois River to St Louis then down to New OrlEEEEEEns on the Mississippi. o_O

I'd rather get a more capable truck and tow it up to the Michigan UP & go check out Beaver Island and the smaller islands that surround it. It's 30 miles offshore.
 
OK...
new dilemma...

Farmer has a duck...
Duck has two geezers and a case of beer...
but he can only raft one geezer or case of beer at a time...
how does Duck get the beer and the geezers upriver to the campsite without leaving a geezer to drink the beer while he ferry's all to the campsite?

:confused-96:
No dilemma....stick old geezers in life jackets....park geezer hinies in inner tube....hook rope to inner tubes to barge...way ya go for a ride....pop top on a can of beer and hit the motor. Red neck style....:toothpick:
 
Well the rain let up a bit.

So I took a 5 gallon bucket & scooped the water off the boat cover so I could get it off without ripping it, and pulled it off just the rear so I could look at the engine.

Animal poop everywhere. :eek:

But the seats are vinyl so it'll clean off.

I didn't look at the whole interior, not even the drivers seat & stuff because it was still raining & I just wanted to snap some quick pix of the engine.

It's a 3 liter Mercruiser engine. Evolved from a Chevrolet 153 engine.

181 cubic inch, 135 hp, 4 cylinder.

Very simple though. No emissions bullshit at all. :D

The boat forums say it's a very popular, reliable engine but not as powerful as a 135 hp outboard would be.

Whenever the grass is dry enough to drive on I'll back it into the shop and go over it with a fine toothed comb. Check stern drive oil, engine oil, probably change it. Check gas tank for water, clean out all the animal poop with the shop vac, check battery voltage, maybe see if it'll start for a few seconds. Maybe actually run it a few minutes if I can find my garden hose ear muffs thing that delivers water to the cooling system. I haven't seen it in 15 years though.

Gonna have the Geezer follow me in my car if we take it out on the water though. I don't know if that S-10 can pull it out of the water at a ramp. :oops:

It barely pulled it home. In 4th I got it up to 55 at one point, eventually. I wasn't pounding on it, just letting it do it's thing & ease it up to speed but on the hills, these mild, gradual rises in elevation we call hills in this part of Illinois, it was losing speed.

Brakes totally suck due to it's oversize wheels, and there's no passenger side mirror.

Drivers side mirror is concave or something. Objects in mirror are FURTHER AWAY than they appear.

I was trying to merge left on Rt 53 in Romeoville for orange barrels & some guy who looked like he was beside the trailer axle waved me over. :confused:

Yeah I definitely need to get one of my own trucks back in service, or get another one.
 
This:

20160816_004252~2.webp

Is a broken EZ-out.

Now what? :dunno:

I had to hit it with the grinder to put flat spots on it just to get it out with channel locks.


All 3 bolts snapped on the blade shaft housing on that mower. I need to get it done & out of here so I can play with the new boat.

I got the other shaft housing out by heating the aluminum casting while holding torque on the bolts with a wrench.

20160816_004355.webp

Tapped the threads clean and used new grade 5 bolts.

But see that hexagonal hole in the bottom? I'm just going to keep drilling through the bolts with larger bits until they're gone, taking the threads in the casting with it, then use that hexagonal hole to hold back a nut. Might have to upsize to 3/8".

20160816_004305.webp
 
Last edited by a moderator:
I drilled the broken bolts out. Drilled them to 5/16" and tapped them for 3/8".

20160816_023030.webp

Everything compares to the picture I took before disassembly of the old deck. All ready to put back on the mower now. :thumbsup:

I'll do that tomorrow when I'm sober. ;)

Geezer was in here bugging me the whole time. I tried to get rid of him by offering him a beer. He usually drinks one then says he's tired and leaves. Instead he drank two or three & then started headbanging to Holy Diver by Dio. o_O

Then he picked this up and said I should smear it all over Sarah's forehead. :rolleyes:

20160816_013518.webp
 
Last edited by a moderator:
She just asked what I was doing out there so I just showed her what I just posted & after I explained what anti-seize compound is, she said it was mean... But she's also laughing.....

Women :coocoo:

:dunno:
maybe she was talking about you when you showed her the anti seize compound:roflmao::D:eek:
 
Back together with new mower deck. I did some mowing with it. Good as new. :thumbsup:

20160816_182439.webp

20160816_182453.webp

New mower deck was $120, not $200.

Just greased it's zerks on the steering spindles & front wheel bearings, replaced a 3" section of fuel line that was dry rotted, and blew the grass off if it. Might drain out a cup or two of oil cuz it's overfull.

When it ran out of gas and started choking, it was blowing blue smoke too. Methinks being overfull on oil made the choke suck oil through the CC breather.
 
Last edited by a moderator:
Shop vac hose isn't long enough to reach everywhere in the boat.

No problem though. I have scrap metal and hose clamps. ;)

20160818_004754.webp

20160818_004905.webp

20160818_004835.webp
 
Free boat when I first took the cover off:

20160816_155929.webp

Here's how it looks now. Gonna take a lot of work. The cover was leaking & animals were living in it for 2 years. Gas smells old.

It's starting battery has 1.9 volts & it's deep cycle is showing 9.4. So they're junk.

20160818_004734.webp

That 2x4 is only there to hold that fan. It's been blowing downward into the boat for two days now, trying to dry it out.

Floor feels solid, so that's good.

Don't even ask how I managed to back an 8 foot wide trailer through an 8 foot wide door then jack it sideways to make room on the right side.

I used my Ranger instead of the S-10 just because it has both freakin' mirrors. :mad:

But as soon as I got the trailer tires over the edge of the cement I unhooked & walked it in the rest of the way by hand with a trailer dolly.

I want to hang the contractor who decided an 8 foot wide, 7 ft tall door located two feet from the south wall was a better idea than the ten foot wide, 9 foot high door 6 feet from the southeast corner, and no freakin' walk-in door as my dad & I put in the floor plan we drew up. :mad:
 
Last edited by a moderator:
No idea what the blower is for, or what that extra switch does.

There's also a stereo but I can't find any speakers. :dunno:

Can't just follow the wires because I can't kneel down on the carpet yet. It's still nasty from whatever critters were using it as a toilet.

20160816_160158.webp

20160816_160056.webp

I laughed when I saw this. I've floated more than that on styrofoam. ;)

20160816_160300.webp
 
It's an inboard/outboard boat. It's a gasoline engine in an enclosed environment. Gas fumes collect. Gas fumes are WICKED dangerous and explosive. You need to run the blower before starting the engine. The starter is the most common part to spark. That switch on the bottom was an aftermarket add on. Look for cracks on the block. Very common on an old boat. If there are cracks it's pretty much junk. Any problems with the outdrive and it's junk. Costs maybe $3,000 to $4,000 to fix anything. Don't get too excited over this boat. You may want to put it into a marine shop. They can do a once over and tell you what your in for.
 
It's an inboard/outboard boat. It's a gasoline engine in an enclosed environment. Gas fumes collect. Gas fumes are WICKED dangerous and explosive. You need to run the blower before starting the engine. The starter is the most common part to spark. That switch on the bottom was an aftermarket add on. Look for cracks on the block. Very common on an old boat. If there are cracks it's pretty much junk. Any problems with the outdrive and it's junk. Costs maybe $3,000 to $4,000 to fix anything. Don't get too excited over this boat. You may want to put it into a marine shop. They can do a once over and tell you what your in for.
Right now I'm still at the point of cleaning up the animal poop so I can begin checking it out.

All I know so far is the engine block looks clean and the bilge isn't full of grease.

It had lots of shredded padding foam under there. I got most of it out with the shop vac but there's a completely shredded piece of 4" ducting under the engine and I can't figure out what it's for.

There's a thing up against the inside of the transom that looks almost identical to an airtronic bunk heater. Might be the blower.

I can't reach very far down into the bilge yet until I clean it up some more because I'd have to kneel on the shit covered back seat and have my stomach and chest on the backrest.

I haven't even figured out how to check the drive unit oil yet. Can't find a dipstick or filler plug.

Same with the engine. Aint no way in hell I can even reach the bottom of the engine & even if I could I can't fit a drain pan under it. :dunno:

I bet professional boat repair shops have harnesses so the mechanics can hang upside down like bats while they're working on the damn things.
 
Last edited by a moderator:

Back
Top