Duck Pond Redneckery


so your going to maynerds today and putting aluminum fittings on your head again:confused-96:
Galvanized steel. Gotta be ferrous metal to block the radio waves.

20161207_200805-jpeg.37687



Yeah going to Me Nerds today.

It warmed up into the 50's and there's a good steady wind too, so it melted 99% of the snow.

That means I won't need the tractor to dig out my trailer. :)

Except the grass will be soggy and the van will probably get stuck. :(

Well I dunno... I plowed the snow in the area I'll be driving on, so it might not be muddy. :dunno:
 
And ended up with ****ty, poorly insulated, drafty crap walls. Or a bunch of bullshit about why we can't incorporate a warehouse pallet rack into a permanent wall, etc.
i didn't say anything about them insulating i would have told them i wanted the heater hung and plumbed and vented and wired up and that i could do the rest of the work myself:rolleyes:. and if it fell on my head there would also be a lawsuit as wello_O
 
Galvanized steel. Gotta be ferrous metal to block the radio waves.

20161207_200805-jpeg.37687



Yeah going to Me Nerds today.

It warmed up into the 50's and there's a good steady wind too, so it melted 99% of the snow.

That means I won't need the tractor to dig out my trailer. :)

Except the grass will be soggy and the van will probably get stuck. :(

Well I dunno... I plowed the snow in the area I'll be driving on, so it might not be muddy. :dunno:
The pic looks like a pilot for SCTV LOL
 
i didn't say anything about them insulating i would have told them i wanted the heater hung and plumbed and vented and wired up and that i could do the rest of the work myself:rolleyes:. and if it fell on my head there would also be a lawsuit as wello_O
I'm trying to get this done without dumping ten grand into it.
 
Well this was more of a pain in the ass than I expected but I made a new face plate for the router that should make the next ones easier.

That's just a scrap piece set in there.

20161226_195918.webp

Menard's doesn't have non-piloted square bits that can plunge 1-1/2" deep so I had to get creative with one that can go 1-1/4".
 
So you have crappy satellite intrnets:confused-96:. Oh and btw I ment cdl dam phone:mad:
I got til 12/29 to get a physical and get it to the DMV. After that, there's more hoops to jump through and as much as I despise the state of the industry I'll probably just permanently change it back to a regular license. Working in this industry with automatic transmissions, e-logs, cameras, emissions controls, dispatchers who think 34 hours a week qualifies as "home time", a CDL just isn't worth the plastic it's laminated with.
 
Homemade router face plate... Because I needed a square one, at least 7 inches wide.

20161226_234947.webp

Carefully positioned C-clamp, this old flat sided one for pickup toppers, serves as the guide.

20161226_235405.webp

Gotta cut twice because the cutting edge of the bit is only 1-1/4".

20161226_235919.webp

This project just got more fun. :)

I should've dug my grandpa's router out of the east barn months ago. :rolleyes:
 
I got til 12/29 to get a physical and get it to the DMV. After that, there's more hoops to jump through and as much as I despise the state of the industry I'll probably just permanently change it back to a regular license. Working in this industry with automatic transmissions, e-logs, cameras, emissions controls, dispatchers who think 34 hours a week qualifies as "home time", a CDL just isn't worth the plastic it's laminated with.

2/3's of the earth's face is covered with water,
yet you've claimed dominion over a fraction of a fraction.

1/5 of the trucking industry is covered by mega-fleets,
yet you can't see an islet for to shelter alee.

If FMCSA were human it wouldn't even be old enough to hold a CDL.

Stay back from the edge of the world...
for there be dragons!

SADDLE UP FUTHERMUCKER!
:mad:
 
I got til 12/29 to get a physical and get it to the DMV. After that, there's more hoops to jump through and as much as I despise the state of the industry I'll probably just permanently change it back to a regular license. Working in this industry with automatic transmissions, e-logs, cameras, emissions controls, dispatchers who think 34 hours a week qualifies as "home time", a CDL just isn't worth the plastic it's laminated with.


Fast forward to two-two-two...
I saw your band...
jumpin' around on stage like a bunch of wounded @Duck 's...

Hrump!
:harumph:

 

Back
Top