Duck Pond Redneckery


View attachment 38592

Man, F* all that. That's way too far into nerd territory. And only COMMIES use metric units. :eek:

Hot tank got down to about 143 and stayed there. It's been hours and hasn't dropped. And that's with both tank valves open, both wall valves closed, 68° FARENHEIT in the shop.



Ball valves. I am amazed by those things. They never leak. Super precision. For 7 bucks.

Unless you use them as a garden hose spigot with crappy well water. :rolleyes:
Since n, R, and V are all constant with your sealed tank, it's easy. The ratio of temp to pressure is constant, as long you remember to use Kelvin.
 
Man, F* all that. That's way too far into nerd territory. And only COMMIES use metric units. :eek:

Hot tank got down to about 143 and stayed there. It's been hours and hasn't dropped. And that's with both tank valves open, both wall valves closed, 68° FARENHEIT in the shop.



Ball valves. I am amazed by those things. They never leak. Super precision. For 7 bucks.

Unless you use them as a garden hose spigot with crappy well water. :rolleyes:
^^ Ignore the nerd. ^^

Didja ever think of using yer lifeline?

o_O

Rearranged,

P = (nR) x (T/V)

Kick out "nR", and P ~ T/V

If ya get pissed at it, an' start stompin' stuff the pressure goes up.

That leaves P ~ T

That says pressure is proportional to temperature in a closed system that doesn't change dimensionally. If yer stuff cools off, the pressure goes down.

So go chug a beer, an' quit worryin'.

:couch:
 
Since n, R, and V are all constant with your sealed tank, it's easy. The ratio of temp to pressure is constant, as long you remember to use Kelvin.
^^ Ignore the nerd. ^^

Didja ever think of using yer lifeline?

o_O

Rearranged,

P = (nR) x (T/V)

Kick out "nR", and P ~ T/V

If ya get pissed at it, an' start stompin' stuff the pressure goes up.

That leaves P ~ T

That says pressure is proportional to temperature in a closed system that doesn't change dimensionally. If yer stuff cools off, the pressure goes down.

So go chug a beer, an' quit worryin'.

:couch:
Dude you guys made it way too complicated.

Here's what someone in the real world does it.

After observing that the pressure was remaining constant except when I'd crack open the supply valve to blow out the fittings, (sloppy pipe goop. I eventually switched to tape) the pressure never dropping enough to kick on the compressor, I opened the valve wide open to simultaneously cool the tank and drop pressure to 120 where it kicks on.

When it was full, it was only slightly warmer than ambient.

And it didn't drop pressure afterwards.

None of that E=MC² bullshit required. :rolleyes:
 
Dude you guys made it way too complicated.

Here's what someone in the real world does it.

After observing that the pressure was remaining constant except when I'd crack open the supply valve to blow out the fittings, (sloppy pipe goop. I eventually switched to tape) the pressure never dropping enough to kick on the compressor, I opened the valve wide open to simultaneously cool the tank and drop pressure to 120 where it kicks on.

When it was full, it was only slightly warmer than ambient.

And it didn't drop pressure afterwards.

None of that E=MC² bullshit required. :rolleyes:
wait what you live in the real world:eek:
 
Done with the hard plumbing.

20170206_234147.webp

Everything else is going to be in rubber hose except for where the line to the hose reel goes through the wall in the upper right corner. That'll just be a barb, 90 and a 6" nipple right into the street elbow on the hose reel.

Same thing with the drain except there will be a 45 or something on the outside to serve as a nut to hold the nipple in the wall.

Nut. Nipples,... rubber,.... :rolleyes:


Anyway the reason for the couplers and rubber hoses is so I can switch them around if I need to put one on the regulator. I don't want the whole system on the regulator. Cranked all the way in it only gives me 120 psi.
 
how much longer before all of this is done:confused-96:. **** i could have had a house built in the time it's taken you to do this:D:stare1:
Yeah, by multiple crews of guys who don't have to make 80 trips to Menard's because they bulk purchase all their materials.

No idea.

Gotta relocate the welder outlet, finish plywooding up the electrical closet, build a door for it then I'm gonna say fuck it and go trucking for a while.
 
Is the compressor radiating cold cause that will cause a drop in pressure.
After finding a leak in the drain tube, before I added a valve to the bottom of the tank, the I had to totally drain it to fix it.

I secured the end of the supply tube to keep it from flopping around and kinking from the jet propulsion, then opened the tank valve all the way. It was extremely loud.

When it was down to about 50 psi on the tank gauge it slowed down and stopped.

The valve was frozen.

I grabbed my propane torch and in a few seconds it freed up and I heard a chunk of ice hit the inside of the steel siding near the electrical panel.
 
I'd never want to be anywhere near an air compressor tank that suffers a sudden massive failure. :eek:

Even if you don't get hit with shrapnel it'll probably give you shockwave injuries or blow out your eardrums. The top half of the tank could go through the roof.

Actually I wonder if there's anything on YouTube. ;)



I think mine might last forever though.

For one it's got some OSHA approval tag on it so it's not a cheapo.

But also because the entire time I've had it, water never accumulated at the bottom due to a leaky "pull the cable" type drain valve.

And now it's going to be downhill about 3 feet, through ten feet of copper before it starts filling up. With frequent draining it'll never pool up in the tank.
 
If I remember I'll ask one of the scientists today why the pressure drops. He has his PhD in fluid dynamics. I think that covers this topic.
 
I wonder if the check valve is leaking. It's just a spring pushing on a seal.

It would leak back through the pump. Nothing to make bubbles in soapy water. Maybe that spring can only hold up to 145 psi because of tiny scratches caused by a piece of gasket material that got stuck in it last summer.

:dunno:
 
Not sure why you care anyways. Every shop I've ever been in the compressor turns on at least every 1/2 hour due to leakage.
 
Is the compressor radiating cold cause that will cause a drop in pressure.

If I remember I'll ask one of the scientists today why the pressure drops. He has his PhD in fluid dynamics. I think that covers this topic.

Ask your scientist that question, I bet you see this:

blog3.jpg
 

Back
Top