Duck Pond Redneckery


The partial walls (so far) of that closet don't transmit noise into the shop but damn,... inside that closet it sounds like there's 50 helicopters landing on the roof. :confused:

Gonna have to cut up some old car tires or something.

You should be able to buy some isolators for a buck or two each.
 
You should be able to buy some isolators for a buck or two each.
At Farm & Fleet they're like,.. I don't remember but I remember thinking I could cut up a car tire cheaper than that.

They're inside a package so I couldn't examine one too well. It just looks like a 4" by 4" square of rubber about half inch thick.
 
th
30dbee_a75db5da0eaf4304ad8c63c5a15a49e4.jpg_srz_980_606_85_22_0.50_1.20_0.webp
 
The conduit to nowhere.... There's just a junction box on the 4th floor. That space only accessible by ladder from the unheated side of the barn.

20170204_230155.webp

I didn't even strip the wires. I just put wire nuts on them, coiled them up and put the lid on the box.

There's two hots, neutral and ground. Not going to hook up that secondary hot in the panel.

:dunno:.

Did that last night. Figure I'll eventually have a hidden sleeper berth up there for when someone is crabby. Power will be available.
 
20170205_142926.webp

There was a security tag built into a non-removable zip tie kind of thing on this roll of copper tubing.

It was around just the part sticking out of the box. And it wasn't pulled tight.

If I rotated the box, it would literally fall off.

At the register, the cashier deactivated it, then struggled with their special tool to remove it, rather than simply slide it off the end of the tube. o_O

:bonk:

Oh,... and this woman looked like she was in her 60's. Not a millennial. o_O
 
View attachment 38558

There was a security tag built into a non-removable zip tie kind of thing on this roll of copper tubing.

It was around just the part sticking out of the box. And it wasn't pulled tight.

If I rotated the box, it would literally fall off.

At the register, the cashier deactivated it, then struggled with their special tool to remove it, rather than simply slide it off the end of the tube. o_O

:bonk:

Oh,... and this woman looked like she was in her 60's. Not a millennial. o_O

It's a girl thang...








:hide:
 
I'd have thought flaring copper was easy. I mean, the tools are pretty self explanatory.

No. :mad:

I made 4 connections. 3 leaked when I sprayed soapy water on them. :mad:

First, I had to grind down the inside of the two halves of the clamp part of the flare tool to get them to close tighter on the copper. Tube would slip instead of flaring.

Then I had to go buy a professional grade tubing cutter and separate reamer because my "Made in Taiwan" tubing cutter didn't do it. Dull blade from cutting galvanized brake lines 20 years ago. So it made too much of a ridge on the inside. Round file doesn't leave a smooth surface.

And the internet person who wrote "set the end of the tube flush with the face of the clamp" is an idiot. Set it 1/16" above it for 3/8 tube and 3/32" for 1/2".

I wasn't going to put a valve on the bottom of the tank for the drain. I just wanted to run copper straight to the valve I'm putting in the wall. But I'm tired of having to warm the fittings when I drain the entire tank every time I gotta redo a flare. It ices up :mad:

So far, 3 don't bubble any more.

This one still leaks.

20170205_194132.webp

That elbow has a plug in it for now just so I can make sure the flare fittings don't leak. The plugs leak but it doesn't matter.
 
When I took that fitting apart there was some red crap in it. Must've been inside the tubing when I bought it. :dunno:

I opened the drain valve on the tank to blow it out. Put it back together and no more soap bubbles.

:yippee-1:
 
This actually went together perfectly. I drilled the two holes perfectly parallel and the right distance apart.

I wasn't expecting it to be that easy. :confused:

Now I'm scared. :stare1:

20170206_144730.webp

20170206_150635.webp

20170206_151556.webp
 
20170206_170601.webp

It fills up to 155 psi and turns off.

After a minute or two it's down to 150.

No leaks anywhere. I checked every fitting on the compressor itself too. No soap bubbles anywhere. I turned off the stereo and the heater and couldn't hear a thing. For a 60 gallon tank to lose 5 psi in about a minute would be audible.

Total mystery.

:dunno:

Just a theory...

Because I just filled it completely, from zero psi, the tank is almost as hot as the radiators in the house. I can't even touch the stainless steel tube from the pump to the tank. In fact, it boiled my soapy water when I checked for leaks on it.

Theory is the tank is full of hot air (shut up @ironpony :mad: ) and as it cools, pressure drops.

:dunno:

I guess the only way to test the theory is to let it cool to room temperature and then start monitoring the gauge.
 
View attachment 38588

It fills up to 155 psi and turns off.

After a minute or two it's down to 150.

No leaks anywhere. I checked every fitting on the compressor itself too. No soap bubbles anywhere. I turned off the stereo and the heater and couldn't hear a thing. For a 60 gallon tank to lose 5 psi in about a minute would be audible.

Total mystery.

:dunno:

Just a theory...

Because I just filled it completely, from zero psi, the tank is almost as hot as the radiators in the house. I can't even touch the stainless steel tube from the pump to the tank. In fact, it boiled my soapy water when I checked for leaks on it.

Theory is the tank is full of hot air (shut up @ironpony :mad: ) and as it cools, pressure drops.

:dunno:

I guess the only way to test the theory is to let it cool to room temperature and then start monitoring the gauge.

You've got an infrared gun, do the math! PV=NRT
 
He flunked algebra too.
No I didn't flunk it. I just don't remember any of it.

And I intend to mail a letter to President Trump asking him to declare algebra illegal.

Not just in schools but everywhere. ;)

If he replies at all I bet it'll be hilarious. :D

PV=NRT

Pressure times volume = nnnnnnn...... rrrrrrrrr..... Temperature??

3 out of 5 ain't bad is it? :dunno:
 
Screenshot_2017-02-06-21-46-02.webp

Man, F* all that. That's way too far into nerd territory. And only COMMIES use metric units. :eek:

Hot tank got down to about 143 and stayed there. It's been hours and hasn't dropped. And that's with both tank valves open, both wall valves closed, 68° FARENHEIT in the shop.



Ball valves. I am amazed by those things. They never leak. Super precision. For 7 bucks.

Unless you use them as a garden hose spigot with crappy well water. :rolleyes:
 
Last edited by a moderator:
20170206_212710.webp

Supply on the left, drain on the right.

I hope I don't smash that gauge putting the upper piece of OSB on the wall. It'll have a hose reel bolted to it.
 

Back
Top