Duck Pond Redneckery


My mechanics shop has been running black pipe for at least 50 years. I should tell him he could have problems in the future.
 
My days of working on cars ended when everything became a sensor. The only thing I do on my own now is change the air filter.
I will be damned if I am going to pay the parts mark up and labor on that:D
for the past few cars, or pick up trucks, i'd buy the K&N air filter. then i'd remove it, wash it, dry it, then re-oil it, reinstall. good for a million miles of service, they claim. saved me money, as the cost of a good air filter at autozone or some other parts stores, averaged about $25 each. in short time, the K&N air filter paid itself.

now i have a lease car, i will do no air filter switching as far as the price of a K&N, i will simply buy a replacement, and as you, save on the huge mark up and labor charges. in fact, in all my years of driving, i do not drive in dusty conditions as some people may do....so i may be able to get away with only 2 new air filters, before i turn in the car at lease end, in 3 years.
 
My mechanics shop has been running black pipe for at least 50 years. I should tell him he could have problems in the future.
He's probably got a filter on it. Or traps at every outlet with a bleed valve.

The crate shop I worked at also had black pipe. Every port where you could hook up a hose, had two valves. One above the tee with the coupler, on the supply side, then about a 6" piece of pipe, and another valve.

The air compressor was drained daily (completely for some reason) and every Friday we had to walk around and crack open the bleeders on all the couplers one st a time before draining the compressor.

It was a big compressor set about 8 feet up on a platform thing too, like I'm doing. Parts washer was under it.
 
No bleed valves, no draining, no nothing. Filter at the compressor outlet, that's it. Pretty much every garage I've ever been in is the same.
 
We have black pipe in our building throughout. The air compressor is the size of a Volkswagon! We have glass filter somethings on every outlet.
 
Good air dryer then.
From the memory banks of my days an instrument tech: There are two filters on any decent air system, one is for water, the other for oil. On our setups, because rig air tended to be wet, we'd run thru a Facet water filter right at the tap, plus we had Parker-Hannifin oil and water filters that were mounted on the remote air supply tanks near our systems. (We used Foxboro CP transmitters, and they had to have very clean, very dry air.) You do something similar and you can use any piping that meets the pressure requirements without worry about scale.
 
The air compressor and the dolly are one unit now. :cool:

20170204_184549.webp

Those gussets were put on after the straps were tightened. With Liquid Nails too. So it's a uniform 5 points of contact with the tank on each..... wooden thing. Whatever you'd call it.

Notched the corners with the bench grinder to save the straps, and keep them in place while I was tightening them.

20170204_165438.webp

And little scraps in the middle between the two main vertical tubes on the dolly keeps it from slipping side to side.

20170204_184607.webp
 
I just measured the tractor bucket. It's 42 inches wide.

Here's the tape measure pulled out to 42".

20170204_185735.webp

I don't know if it's safe to just put it in the bucket and lift it that way with basically just two points of contact in the bucket but I'll gonna put it in there, lift it up just high enough to slide a wood block under it and see how stable it is.

Securing it to the dolly was for pulling it up a ramp. But I'm thinking the tractor will still be easier.
 
Well this ain't gonna f'kin work. It wobbles way too much even if I shim it to compensate for the bent up bucket. :mad:

20170204_204122.webp

I took the bucket's side wings off, and the 8 trillion ton grader blade to give me more room to maneuver the tractor in here too. :mad:

Oh,.... last time I put those side wings on I used stainless steel hardware.

4 of them were LOOSE but as I unscrewed them, they got tighter and tighter until I eventually had to snap them with a cheater bar. Threads weren't damaged either. :dunno:
 
The Geezer trying to direct incoming wind from the doorway to create a circular air flow to vent the tractor exhaust fumes faster.

:coocoo:

20170204_220943.webp
 
The partial walls (so far) of that closet don't transmit noise into the shop but damn,... inside that closet it sounds like there's 50 helicopters landing on the roof. :confused:

Gonna have to cut up some old car tires or something.
 
th
 

Back
Top