Duck Pond Redneckery


Well I just went out to the barn just to turn the heat back on.

It was -1° outside when I turned it off at midnight. Right now it's 15°.

Thermostat said it was 34° in the workshop, and half the south wall and about a third of the east wall isn't insulated yet.

I felt the steel siding because sometimes direct sunlight warms it up but it was freezing cold.

I know it's not residual heat from having the air temp at 68° last night. Not with such large uninsulated sections left.

All I can think of is the floor. It's been around 50° the past few days.

If it's absorbed enough heat to still have it that warm (compared to outside) after 13 hours, it's evidence that a heated slab is the way to go if I ever start from scratch.


My dad knows a guy who chopped out the floor in his hangar and had a new slab poured, with the heating pipes in it. Says that it takes about a third as much propane to heat his hangar that way vs the forced air convection he'd had in there before,though he still uses the forced air furnace on occasion when its extremely cold.
 
Huh?
cute-cat-looking-excited-cats-wallpaper-1366x768.jpg


...did somebody say .....sandbox?..




I'd like to build a big sand box.

hectic-realtor-cats-07.jpg
 
Not smartphone friendly.

I can only see the left half of that page. Can't even scroll to the right.

Isn't THAT ironic? ;)

Damn commie bastard. :mad:
Go buy a phone that was made in this century cheapskate!

Dang skinflint! :mad:

Probably not going to find a thermostat out of a box that's going to let you go below 40° or so. Most folks don't want their pipes ta freeze.

:rolleyes:
 
Last edited:
Yes, my idea would be in a metal box with a 2x24 display and some buttons. A microprocessor and a real temp chip. A plug in 5v power supply. It would also give you all the options like setback and turnon at a certain time and the swing between turning off and on depending on the temp like a 5 degree spread or 10 degree or whatever. I have pretty much the parts to build like 20 of them right now here at home. I even have a Class 1 Bluetooth chip that has a distance of 300' so he could control and monitor from inside his house!

And yes, it would be written in C. I've done this shit a thousand times and have the code for most all the routines I would need.
 
The floor in here is 32° right at the southwest corner underneath a tool box where there's no airflow but it's still 46 degrees in the middle. Temp drops near the pallet rack wall too.

Surprising that the slab only lost 1 degree farenheit with the heat off for 13 hours.
Heated floors are the only way to go.
My buddy's shop has the wood boiler outside and it feeds his house as well.
Those things cost like ten grand though. Plus you gotta bury insulated pipes into the buildings.
 
It's cold as fuck near this wall even though the wood around the window is showing 75 degrees because of the sunlight. The floor near the wall is 33°.

The air being sucked into the top of the fan is 70°.

Going to leave this set up while I go eat.

Probably won't make much difference.

20170107_141324.webp
 
We have some fancy expensive thermal color video cam at work. It's pretty cool looking at stuff. Even your shoes
I need an infrared viewer. Like goggles that show the hot spots.

Didn't some nerds get some media attention for using something like that to "see" through women's clothing?

I'd of course, certainly do that too,... :rolleyes:

But what I really want them for is to walk around the house and the workshop to see where all the poorly insulated areas are so I can fix it.
 
I need an infrared viewer. Like goggles that show the hot spots.

Didn't some nerds get some media attention for using something like that to "see" through women's clothing?

I'd of course, certainly do that too,... :rolleyes:

But what I really want them for is to walk around the house and the workshop to see where all the poorly insulated areas are so I can fix it.

It's not infrared, it's thermal you want like I posted above.
 
Didn't some nerds get some media attention for using something like that to "see" through women's clothing?

I'd of course, certainly do that too,... :rolleyes:

Sony videocams from the 90's, I think. The CCD was fairly effective in IR, so if you put a filter on the lens to knock out the visible, VOILA! Nipples galore!

It's not infrared, it's thermal you want like I posted above.

ummm, infrared is what thermal cams 'see'
 
The one we have at the lab is a handheld camera connected to some computer box then a display. They use it to inspect the welds on a special battery box for the armed forces stuff.
 

Back
Top