Duck Pond Redneckery


One of the damaged pieces I removed did this when it hit the ground.

20160919_182408.webp

Insulation exposed.

Cutting steel panels with scissors, while kneeling on styrofoam insulation is not easy. o_O

But I did it cuz I'm Super-Duck. :D

20160919_182229.webp

I got one new piece up. It's actually left over from the construction of the barn in 2008 and was lying outside in the mud for all that time and didn't rust.

It was way more of a pain in the ass to slide the new piece underneath the upper part to shingle-lap them. It was getting stuck on the nail heads that hold down the insulation. And the Geezer was nowhere to be found so I had to jam my hand in there and lift it over the nail heads while pulling upwards on the bottom of the new sheet with a ratchet strap with my other hand, while trying not to pull hard enough I'd start sliding down since I was on a panel that doesn't have a scaffolding below it. :mad:

Lots of loud profanities were uttered.

20160919_190746.webp

It's only pinned down well enough to hold it for tonight. It's getting dark & mosquitoey.

And I still need to wash the mud off the other piece that's going up there. :toothpick:
 
Here's a question for you nerdly rednecks here. Serious now, need some input.

In the flood aftermath I had to pull all the insulation off the bottom of the trailer cause it got soaked in the "waters" and ruined. Fiberglass mat that went from 6 inches thick to about 1.5 or so. Full of mold as well natch. Working by myself, it's been a beach of a job. Weather sucks; pretty much long periods of heavy rain every day and having to repair/replace inside stuff that got wet and moldy too.

Anyways.....

It's just about time to replace the insulation. I've looked over the options and brought it down to 3.

1. Fiberglass mat (as original). Material costs for the cheapest, lowest R value is around $800 and it needs a plastic sheeting cover for about another $300. Labor will be a female dog and longevity is suspect as seen by the original. Least favorite for me and my old back.

2. Spray foam. This is basically MDI/TDI mixed with Polyols. Real familiar with these cause it's what I haul. Dangerous stuff. Lowes has DIY kits that sell for around $800 each and cover approx 600 board feet each. I need 1280, so looking at min 2 kits. That's at least $1600 just for material. Tried contacting contractor for this. No response except for 1. Not worth their while, would charge over $1000 just to "prep". No guarantee for application. At least 3 months before they could even look at it cause they're doing "real houses" via FEMA

3.Poly Pro insulating board. Basically a 1 inch thick close cell 4 ft x 8 ft closed cell board with one side coated in reflective foil. Materials would run about $640 (40 sheets) to cover the 1280 ft area. This is what I'm leaning to right now.

So, Duck, et al.... how would you proceed?


Okay...
leave the nerds out of this.
They don't have the skill set required to advise on such matters.

BTW,
WTH is the matter with you!??
You're going to give rednecks a bad name.
It wouldn't surprise me to see Luzi-anna extreme vetting Canuckians i the near future if this gets out.
:mad:

You need a poor conductor with a high flash point & low burn rate [just to state the obvious] so as stated above, nothing beats dead air for cost effectiveness.

Like @Duck said, if you could get a good seal above plastic sheeting you goal would be accomplished but that is easier said than done.
You have to plan for the inevitable breech[es] so you need something of substance to prevent a total failure with the first little tear.

You can produce your own all natural and very effective insect repellent & fire retardant with borax and boric acid.
I have a couple of recipes around here somewhere but google will yield dozens of results in a tenth of a second so...

Now your options are expanded greatly.
Wood, paper, cardboard, etc...

But that's plan C.
:D

Here's plan A...
There are countless tear-outs & rehabs in progress in your area, many of which are insurance jobs.
You can insulate the crap out of your sub floor with free materials for the asking.
The contractors doing these jobs are paying top dollar right now for refuse removal so they'll be happy to let you take a coupla-few yards off their hands. The people doing tear-outs aren't going to bother trying to salvage much of anything.

If you don't have a pick-up or trailer you can probably get one of the workers to deliver after work for a fee.

Plan B...
There are probably scavengers [like me] collecting materials already and selling them on craigslist for half price or less.

You're welcome.
:)
 
Put your pants on.
:)

dumbass
Nope.

I was wearing shorts and had to keep pulling the belt up to my rib cage like an old geezer to keep the legs of the shorts off my knees.

Denim doesn't grip that steel but bare skin does.

Especially on the screw heads. :mad:
 
20160920_111907.webp

Looks fine from the ground.

You can only see it from the sod farm's property anyway.

That's why I was tempted to patch it with some of the leftover red siding because we have plenty of that. :toothpick:

It was their damn tree that put the hole in the roof. They should've fixed it.
 
The insulation on the inside...

I had a plan to wedge a 2x4 under it to hold it while glue dries.

20160920_110445.webp

But all I did was push it up back into place & it fit tightly and stayed put.

20160920_110535.webp

So f* it, good enough. :D
 
Whatever brand that steel is, whatever they painted it with is amazing though.

The piece I cut up for the patch I had set along the west side of the house 8 years ago to keep weeds down and to protect the dirt beside the foundation from erosion caused by rain running off the edge of the roof.

I've walked on it so many times because the garden hose spigot is on that side.

I never thought that stuff would end up on the barn but geez,... It didn't rust lying directly on dirt for 8 years.

There were some splits & dents from being stepped on & run over a million times with the lawnmower but there was a 9 foot section in the middle that was intact.

The other panel was underneath the stack of red steel, also directly on dirt but wasn't bent.

So yeah, I'd say that stuff is good roofing material.

Especially if it's on top of plywood because that tree probably wouldn't have punctured it if it was.
 
Okay...
leave the nerds out of this.
They don't have the skill set required to advise on such matters.

BTW,
WTH is the matter with you!??
You're going to give rednecks a bad name.
It wouldn't surprise me to see Luzi-anna extreme vetting Canuckians i the near future if this gets out.

Oh, I know already what I'm gonna do, but never hurts to ask.

Here's one for ya's. The foam sheets have a metallic film on one side. So does the "shiney side go up (towards the floor) or down (the ground)?
 
Oh, I know already what I'm gonna do, but never hurts to ask.

Here's one for ya's. The foam sheets have a metallic film on one side. So does the "shiney side go up (towards the floor) or down (the ground)?
Radiant barriers need an air gap, so shiny side down so the foam provides the gap. If you put it up, the foil conducts heat due to touching the floor and isn't nearly as effective.
 
So,
@Duck ...
I hooked a 12v bilge pump up to a shattered solar panel this evening.
I don't recall the rated volume but it filled a 5 gallon bucket at 3' of lift in about 30 seconds so the volume was about 600 gph.
[That's 1" pipe for scale]
That was about 5 pm [0500 @Sinister :)] so it wasn't full sun but a lot more than you'd get in Dec or Jan.

zb3up1x8Xz5wq_Ezg06ksUTr5KoI0dBoBaoi-FHhPxfnLwo-D70sNSZFGgd3sP6NUyGQoJE5XvhNzK5PFKornJum9bTdB60dloS-xrqnu0y5-xs_vjC2iJHaWAo6lkKhdOxgf3KEVXCM1AYPz8GfNe5s2K3rDNm-kRaQlbJe7lCWmXy7dJHPY8deK3Mq5igNVPstpelAUP5bgonskimgk8UuDhAEAnfcHlTKPWJfE_A4XhqthmIjMJekjQ1nLJftBk9hF_Gm7H-DenWvFTDIwKIvEW4BpQ1xXDQLibjcGJHlVyW78eLGjbvhebSYmwLJqdm2dYRtOeqfyjiKzcKeucSyXCK1CyyddilCI4UFFzR32KPEdT3XyYXIacAlEmZHYBhB_VWS4nWAYfaEKdIbQMe0mtLjYRi5zC2btdoYb9HPxzrDTS8PTJD1KK7QDhEfbD69MHMw3_80BPDCMXW0K7XYC1VofKYxSoe7Ls8hCS3VmrqxfOuqHcBBEe3WLl6pWMuniG40VYA4Dh2Mj9291egOFcxrvbjr_G_ZXVAA8KDELcdlgpuQDTaBSRLacq5d4mLPat9rx9e4WSwcEYOTuI1Y6Z4m-rS7tx9qe3J5wqbqnGTR=w211-h220-no



 
Last edited:
So,
@Duck ...
I hooked a 12v bilge pump up to a shattered solar panel this evening.
I don't recall the rated volume but it filled a 5 gallon bucket at 3' of lift in about 30 seconds so the volume was about 600 gph.
[That's 1" pipe for scale]
That was about 5 pm [0500 @Sinister :)] so it wasn't full sun but a lot more than you'd get in Dec or Jan.

zb3up1x8Xz5wq_Ezg06ksUTr5KoI0dBoBaoi-FHhPxfnLwo-D70sNSZFGgd3sP6NUyGQoJE5XvhNzK5PFKornJum9bTdB60dloS-xrqnu0y5-xs_vjC2iJHaWAo6lkKhdOxgf3KEVXCM1AYPz8GfNe5s2K3rDNm-kRaQlbJe7lCWmXy7dJHPY8deK3Mq5igNVPstpelAUP5bgonskimgk8UuDhAEAnfcHlTKPWJfE_A4XhqthmIjMJekjQ1nLJftBk9hF_Gm7H-DenWvFTDIwKIvEW4BpQ1xXDQLibjcGJHlVyW78eLGjbvhebSYmwLJqdm2dYRtOeqfyjiKzcKeucSyXCK1CyyddilCI4UFFzR32KPEdT3XyYXIacAlEmZHYBhB_VWS4nWAYfaEKdIbQMe0mtLjYRi5zC2btdoYb9HPxzrDTS8PTJD1KK7QDhEfbD69MHMw3_80BPDCMXW0K7XYC1VofKYxSoe7Ls8hCS3VmrqxfOuqHcBBEe3WLl6pWMuniG40VYA4Dh2Mj9291egOFcxrvbjr_G_ZXVAA8KDELcdlgpuQDTaBSRLacq5d4mLPat9rx9e4WSwcEYOTuI1Y6Z4m-rS7tx9qe3J5wqbqnGTR=w211-h220-no




There are two or 3 of those things in that boat.

I oughta try growing some hydroponic tomatoes down by the creek next year.
 
There's a triangle shaped piece of land right by here where two cricks merge maybe 1000 feet south of the road.

They didn't do much with it for years & years. They grew corn there this year.

Maybe they'll sell it to me. I'm guessing about 15 acres.

Right at the point of the V would be a perfect spot to grow veggies and fruits.

The creeks are about ten feet below grade most of the year. So I'd need an irrigation pump.
 

Back
Top