Duck Pond Redneckery


I actually have an idea to just buy a pontoon boat and modify it for shallow draft.

My 16 footer I've posted pictures of can, according to the math, carry 2000 lbs in 6" of water minus it's own weight which feels like about 150 lbs.

Actually more, because the wood that adds all the weight can float too. :dunno:

Anyway the idea to modify a pontoon boat is to simply hang a raft underneath it between the pontoons with some kind of hand crank winch system so if I get stuck on a sand bar and there are no trees within winching distance, I can drop the raft, then crawl on top of it and use scissor jacks (or something... camper leveling jacks?) to transfer weight from the pontoons onto the raft.

In that part of the river I'd never be going fast enough to get beached so hard that shifting some weight onto a raft won't reduce the draft enough a couple of guys can't get in the water and push it back into deeper water.

Especially on a weekend when all we gotta do is wait for the next fishing boat to go past & flag him down and ask him to backtrack a bit and haul ass past us to give us some waves to help float it out.




Or,...

I could just get a pontoon boat someone is selling cheap because the pontoons are damaged or destroyed, and remove them & set the whole thing on styrofoam. ;)

How big is a pontoon boat? Like 8 feet wide by what? I bet they vary from 18 to 24 feet.

With a whole foot of polystyrene, I could put 12,326 lbs of flotation under it.

What's the rated weight capacity of a typical 24 foot pontoon boat? I bet it's nowhere near 12,326 lbs. ;)
 
And, BTW...
I'm sure you've researched raft construction since you started on your first one but why wouldn't plywood secured to 4" or 6" PVC conduit pontoons allow less draft than a full sheet of polystyrene on the surface.
Seems to me that you could estimate the displacement and achieve everything from empty to maximum payload within a coupla inches of the surface.
You could even fill them with foam if you were concerned about a breach.
I was just thinking....

Though the PVC pontoons would draft more than flat styrofoam, it's not going to draft the 4 inches the raft usually does when loaded up like the Clampetts moving to Beverly Hills..

The amount of water displaced to make it float will be the same either way though.

I'm thinking that maybe the pontoons would be better for this application because of the shape.

Less drag. It's really easy to make a cone shape out of pretty much anything & glue it to the ends of the pontoons.

I think they even sell cone shapes of styrofoam at craft stores that I could coat with bondo or something to make a hard exterior surface.

And then there's the fact that with pontoons I could eliminate the need for 2x4's running lengthwise for strength so two of us could pick it up from opposite ends to carry it out of the water without it sagging in the middle.
 
I was just thinking....

Though the PVC pontoons would draft more than flat styrofoam, it's not going to draft the 4 inches the raft usually does when loaded up like the Clampetts moving to Beverly Hills..

The amount of water displaced to make it float will be the same either way though.

I'm thinking that maybe the pontoons would be better for this application because of the shape.

Less drag. It's really easy to make a cone shape out of pretty much anything & glue it to the ends of the pontoons.

I think they even sell cone shapes of styrofoam at craft stores that I could coat with bondo or something to make a hard exterior surface.

And then there's the fact that with pontoons I could eliminate the need for 2x4's running lengthwise for strength so two of us could pick it up from opposite ends to carry it out of the water without it sagging in the middle.
Yeah, and a snag won't go thru pvc like a hot knife thru butter, either. I think in any mobile application, you'd want kemlite or something similar on the bottom to protect the foam sheet.
 
Yeah, and a snag won't go thru pvc like a hot knife thru butter, either. I think in any mobile application, you'd want kemlite or something similar on the bottom to protect the foam sheet.
My rafts just have luaun underlayment. 1/4" thick hardwood plywood. And the styrofoam is totally exposed on the sides.
 
Wrong. I was 100% sober when I walked into the metal barn during a lightning storm.

But I was carrying a case of beer.

:D

OK...
new dilemma...

Farmer has a duck...
Duck has two geezers and a case of beer...
but he can only raft one geezer or case of beer at a time...
how does Duck get the beer and the geezers upriver to the campsite without leaving a geezer to drink the beer while he ferry's all to the campsite?

:confused-96:
 
I was just thinking....

Though the PVC pontoons would draft more than flat styrofoam, it's not going to draft the 4 inches the raft usually does when loaded up like the Clampetts moving to Beverly Hills..

The amount of water displaced to make it float will be the same either way though.

I'm thinking that maybe the pontoons would be better for this application because of the shape.

Less drag. It's really easy to make a cone shape out of pretty much anything & glue it to the ends of the pontoons.

I think they even sell cone shapes of styrofoam at craft stores that I could coat with bondo or something to make a hard exterior surface.

And then there's the fact that with pontoons I could eliminate the need for 2x4's running lengthwise for strength so two of us could pick it up from opposite ends to carry it out of the water without it sagging in the middle.

And besides that,
you'd have two [four if you bring a saw] torpedo tubes that could be deployed in the event of zombie apocalypse.
:)


Compressed air, propane and a detonator...

@Sinister is getting weird...
you might have to take him out.
:(

;)
 
OK...
new dilemma...

Farmer has a duck...
Duck has two geezers and a case of beer...
but he can only raft one geezer or case of beer at a time...
how does Duck get the beer and the geezers upriver to the campsite without leaving a geezer to drink the beer while he ferry's all to the campsite?

:confused-96:
Simple.

Duck floats one geezer to the campsite with the case of beer.

Duck brings the case of beer back with him to get the 2nd geezer.

By the time he gets both geezers to the campsite, the duck has drank all the beer and is so drunk he thinks he actually read your post correctly the first time.

:D
 
OK...
new dilemma...

Farmer has a duck...
Duck has two geezers and a case of beer...
but he can only raft one geezer or case of beer at a time...
how does Duck get the beer and the geezers upriver to the campsite without leaving a geezer to drink the beer while he ferry's all to the campsite?

:confused-96:
OK, haul the beer halfway to the campsite & hide it in some weeds on an island.

Come back and ferry the geezers to the campsite one at a time.

Then go back halfway to get the beer.
 
Though the PVC pontoons would draft more than flat styrofoam, it's not going to draft the 4 inches the raft usually does when loaded up like the Clampetts moving to Beverly Hills..

The amount of water displaced to make it float will be the same either way though.

I'm thinking that maybe the pontoons would be better for this application because of the shape.

Less drag. It's really easy to make a cone shape out of pretty much anything & glue it to the ends of the pontoons.

I think they even sell cone shapes of styrofoam at craft stores that I could coat with bondo or something to make a hard exterior surface.

And then there's the fact that with pontoons I could eliminate the need for 2x4's running lengthwise for strength so two of us could pick it up from opposite ends to carry it out of the water without it sagging in the middle.

You could possibly even fill the pontoons with expanded foam to a point and leave a void aft that would swamp during conveyance and drain out once beached.

Baby got back.
:)

;)
 
OK, haul the beer halfway to the campsite & hide it in some weeds on an island.

Come back and ferry the geezers to the campsite one at a time.

Then go back halfway to get the beer.


BASTARD!
:mad:

I was kind of planning to get hammered one way or the other.
But NOOO!
You had to go and solve for....
WAIT!!
WHAT!?

You stashed the beer in some weed?
o_O
Well, dammit boy...
I guess you didn't know me n Jerry could smell...
and swim!!
:)

Have a nice weekend...
dumbass.
:D
 
Speaking of geezers,..... :eek:

That ornamental concrete place still had some crap so we went to get two shelving units, a piece of aluminum C-channel & some expanded metal sheets.

I put one strap on, and the geezer hopped in the truck and started it & took off. :eek:

I yelled at him to stop and he jammed on the brakes, sending the 20 foot stick of C-channel flying off the top of the trailer and almost smashed his rear window. :confused:

Somehow I managed to convince him to hold his horses til I could get the stuff secured to the trailer. :rolleyes:


20160729_162918.webp
 

If you distribute the weight just far enough aft so that the forward end of the pontoons ride just above the water line you will have achieved a a more perfect [geometric] plane than anything you could fashion from hobby-lobby.
 
If you distribute the weight just far enough aft so that the forward end of the pontoons ride just above the water line you will have achieved a a more perfect [geometric] plane than anything you could fashion from hobby-lobby.
Still totally squared off in the rear though.

Screenshot_2016-07-30-01-31-59~2.webp
 
I should put the trolling motor on the solar panel raft with no battery and see if it moves.

Turn it loose on Cedar Lake in Indiana & follow it with a boat and see if it gets moving very fast.
 
OK...
new dilemma...

Farmer has a duck...
Duck has two geezers and a case of beer...
but he can only raft one geezer or case of beer at a time...
how does Duck get the beer and the geezers upriver to the campsite without leaving a geezer to drink the beer while he ferry's all to the campsite?

:confused-96:
Inner tube the two geezers and keep the beer on the raft.

maxresdefault.jpg
 
Something I've wanted to toy with since I started with the grow beds and fish tanks is using 12v bilge pumps for propulsion.
It seems that you could fashion thrusters from the bilge pumps if you position them in the front for intake and plumb the discharge to the rear.

Pond pumps are rated at the point of discharge while bilge pumps are rated at 3 feet of lift...
HUGE DIFFERENCE!!
You can buy an 1100 gph bilge pump for under $20



Jet-skis do get more than their share of douchebags. I keep looking for the IROC-Z sticker hidden on them somewhere.

YIPPEE KI YAY!!!
:pickle:

:crash:


 

Back
Top