Duck Pond Redneckery


How to get plywood way the f*** up high without ropes or pulleys:

Stretch out step ladder. Position so lower part of ladder is on the top, creating something the plywood can catch on.

20160624_145323.webp

I had to stand on a chair to shove it the last two feet up the ladder til it was locked by the top of the lower part of the ladder.

20160624_161605.webp

Then I used the other ladder to get up to the third platform and pull it up onto the 4th.

20160624_162253.webp

I set it in place & jammed the 2x4s in from underneath.

Piece of cake. :thumbsup:

But it's hot as hell up there even with both big doors open, a breeze, and full soffit & ridge vents. :mad:
 
You call that plywood? Is it laminated veneers or glued chunks and shavings?

The grain seems to be going every which way in small sections, which would mean Chipboard here.
 
You call that plywood? Is it laminated veneers or glued chunks and shavings?

The grain seems to be going every which way in small sections, which would mean Chipboard here.
It's called Oriented Strand Board here. OSB. It's what they make houses out of these days.

Wood chips mixed with glue & pressed into boards.

It's cheaper... But they have to compensate for its weakness by using a closer spacing for studs, trusses & floor joists. Which means they spend more on structural lumber.

:bonk:

Anyway here's my "quit screwing around & throw me my damn tape measure" look.

View attachment 35154
 
Last edited by a moderator:
OSB? fancy name.

It's just Chipboard here. Made from Chips of wood... logical name, eh?

Stuff made from almost dustlike bits is Particle board, thats what most IKEA type flatpack or cheap shelving is made from that.

I'm off outside shortly to clean up and check the ashes of yesterdays bonfire. it was about 8 foot tall and around 10 feet round. Not the largest we've had by any means, but a reasonable size.
 
OSB? fancy name.

It's just Chipboard here. Made from Chips of wood... logical name, eh?

Stuff made from almost dustlike bits is Particle board, thats what most IKEA type flatpack or cheap shelving is made from that.

I'm off outside shortly to clean up and check the ashes of yesterdays bonfire. it was about 8 foot tall and around 10 feet round. Not the largest we've had by any means, but a reasonable size.
I've heard it called chipboard, flake board, etc.

I call it garbage.
 
Pressboard... Lots of names for it. I hate seeing it get applied to exterior house walls, especially in the NorthWest. The stuff is fine as long as it stays dry. But get it wet and it turns to mush.
 
Pressboard... Lots of names for it. I hate seeing it get applied to exterior house walls, especially in the NorthWest. The stuff is fine as long as it stays dry. But get it wet and it turns to mush.
I've got two extra sheets. Funny how different they look since I blew all the concrete dust off of them.

20160624_211446.webp
 
You saw a mouse, didn't you?
o_O

:D

20160624_185143-jpeg.35154
 
My pink Ching-Chang Ding-Dong trailer's wood was rotted so I pulled it off to replace it.

It looked like crap. Rusted really bad in critical places.

20160626_164847.webp

20160626_155340.webp

That's not my foot so shut up... :mad:

20160626_155527.webp

So I yanked it apart.

All the way apart and stripped & painted it all up nice n purty like...

20160629_170528.webp

20160630_232706.webp

20160629_221951.webp

20160630_203535.webp

20160630_203524.webp

I added a weld to these brackets on the web side of the channel to beef it up.

20160628_203057.webp

Damn communist metric garbage replaced with American Freedom size hardware. :usflag:

20160701_210352.webp

I even painted the wheels.

20160629_221958.webp

I pumped 20 shots of grease into the hub zerks.

And labeled the tires with a paint pen.

20160701_205221.webp

Then put it back together.

20160701_205150.webp

It's not a folding trailer any more. I added a few extra bolts to hold it open.

After I recover from the hangover I'm going to have after next week's raft trip I'll put plywood on it & fabricate some kind of steel side kit.

The side kit will be 1-1/2" electrical conduit, probably. So since paint doesn't stick to zinc I'll have to paint the welds silver so it'll somewhat match the zinc and not look too horrible.
 

Back
Top