Duck Pond Redneckery


I have to teach the geezer to use a cordless drill.

The geezer,... with a power tool. :stare1:



Unless @Blood is in the area... o_O



These 2x4's for the door frame are bowed.

I've got it fitting perfectly, shimmed all the way around with 1/4" shims.

20170210_223334.webp

But the outer door skin is going to overlap.

The shims are in the way of that. And they're screwed to the outer door frame cuz I had to tap the inner one in.

The inside skin will fit perfectly but...

It has to be screwed on from the inside.

And the door frame needs to be screwed to the opening frame to take out the bow in the middle. o_O

So,... Once I screw it on, I'll be trapped in the electrical closet. :confused:

20170210_224802.webp

So I will have to rely on the geezer to remove the screws. :stare1:

But I only have one cordless drill... :oops:

I guess I can use the AC drill so he can have the cordless out there. :headscratch2:
 
Never mind... :rolleyes:

I just cut another 26-1/2 and hammered it into the middle to hold against the bow. I don't plan on having a center piece in the door because of weight.

20170210_225535.webp

I can just screw the inner door skin on then kick the fuck out of the door until it falls into the shop. ;)

Worst case scenario I'll have my phone in my pocket. :toothpick:
 
I have to teach the geezer to use a cordless drill.

The geezer,... with a power tool. :stare1:



Unless @Blood is in the area... o_O



These 2x4's for the door frame are bowed.

I've got it fitting perfectly, shimmed all the way around with 1/4" shims.

View attachment 38686

But the outer door skin is going to overlap.

The shims are in the way of that. And they're screwed to the outer door frame cuz I had to tap the inner one in.

The inside skin will fit perfectly but...

It has to be screwed on from the inside.

And the door frame needs to be screwed to the opening frame to take out the bow in the middle. o_O

So,... Once I screw it on, I'll be trapped in the electrical closet. :confused:

View attachment 38687

So I will have to rely on the geezer to remove the screws. :stare1:

But I only have one cordless drill... :oops:

I guess I can use the AC drill so he can have the cordless out there. :headscratch2:

I'm on sabbatical.
:)
 
Electrical closet???? WTF is in there, a small fuse box? Seems like a bunch of wasted space now?
It sounds like something in a large building with 1400 outlets and things that make buzzing sounds but I don't really know what else to call it.

It's a storage closet that happens to have a breaker box in it.

It's only purpose is for leaving that wall accessible for expansion of electrical circuits, and not having to insulate and wall off that mess.

I did the interior walls with scraps so it's easily removable to run more conduit through the walls.

I also made a 4" x 4" section of the ceiling cordoned off internally with 2x6 scraps and insulated only with scraps of polystyrene so I can drill straight through it in a year or two when I get around to tearing down the chicken coop and building a two room heatable tractor shed/man cave on that slab. I'll need to run power to it. There's already a PVC conduit through the southeast corner of the shop for that. Capped off for now.




The closet is not really wasted space though. I plan on putting high mass objects in it that are somewhat tool related but rarely used.

My three big bulky high torque drills, the tractor's tire chains, my milk crates full of tow chains,... stuff I want in the shop but don't want sucking heat out of the air when the heat has been off for weeks and I just want to heat it for a few hours to fix a car or something.

If there is room, I have a bunch of electric motors and small engines I'll put in there.
 
Last edited by a moderator:
The two room tractor shed... plan is to have a small room just barely big enough for the Ford tractor, very well insulated, with subfloor, so it can be kept at 40° all winter cheaply, or just kept cold but heated to 65 as soon as it starts snowing.

Just gotta figure out how to vent the gasoline vapors without heat loss. Because explosions are bad.

Until then I'll just be keeping the tractor in the workshop so I can warm it up when I need it.
 
Forgot to leave the inner 2x4's exposed for the outer door skin to set on.

20170211_201851.webp

Ain't taking all that crap apart to remove the sheathing so I set the circular saw to 7/16" depth.

20170211_201906.webp

Old school guys would've used a hammer and chisel to chop out the part at the top and bottom the circular saw can't get to.

Not me. ;)

This thing worked perfectly. :D

20170211_201945.webp
 
The two room tractor shed... plan is to have a small room just barely big enough for the Ford tractor, very well insulated, with subfloor, so it can be kept at 40° all winter cheaply, or just kept cold but heated to 65 as soon as it starts snowing.

Just gotta figure out how to vent the gasoline vapors without heat loss. Because explosions are bad.

Until then I'll just be keeping the tractor in the workshop so I can warm it up when I need it.
explosions are fun:D:eek:
 
The insulated closet door.

20170212_002126.webp

I coulda probably finished it tonight but I fucked up the cheap Chinese bearings tapping them into the holes with a piece of wood. :mad:

20170212_002002.webp

20170212_002036.webp

So I enlarged the holes slightly with the router and I'll put it together with new bearings tomorrow.
 
Somehow WOOD crushed the outer bearing races inwards, buckling the inner races just enough they're stiff as hell.

They're for the latch. A piece of flat stock will be welded to one end of the shaft and will fall in behind the door frame to hold it shut.

On the inside the handle will be welded to a set screw collar and I'm going to nick a flat spot in the shaft with the grinder for the set screw to bite into.


I did almost the same thing with a bicycle wheel axle and hub and it worked flawlessly for years, until the realtor made us tear down that shed.
 
Old school guys would have done it right the first time.
Probably. :rolleyes:

I'd like to go to the house my grandpa built. It's in Lockport, IL.

Well it started as a bungalow but he kept adding onto it,.. himself. Then he built a barn workshop.

It would be cool if whoever lives there now would let me look at his craftsmanship, since I was only like 12 or 13 when he sold the place.

My dad keeps coming into the shop and looking at what I'm doing, smiling and saying things like "it skips a generation". And he takes pictures of everything and sends them to his sister.

All I've got as an example of his (construction) work is the workshop he built in Tennessee but he was in his 70's at the time. Very clever and amazingly simple lock mechanism on a little sliding door on the workshop half basement. (it's built into a hill.) Although it's extremely simple I can't describe it without pictures.
 
Last edited by a moderator:
Inside the electrical closet.

20170213_002150.webp

To open it from the inside, grab the handle, pull to release the tension on the latch bar & flip down on the corner of the bar.

20170213_002201.webp

The vertical flat stock keeps it from being bent open. The wood block inside it keeps it from bending if the door is slammed shut on the latch bar.

This is a replica of a door and latch I made on a shed when I was a teenager except I used a bicycle wheel axle & hub.

The outside knob:

20170212_225528.webp

The flat stock is welded to a set screw collar.
 
Except tonight, this is the door latch.

20170213_005645.webp

I took it all apart to paint the parts that aren't galvanized.

I want it to stay shut tonight so I can check the temperature differences inside & outside of it tomorrow morning afternoon.

When you close that door, it makes a "whoosh" sound. If you're closing it from the inside, you can see the steel siding wiggling in and out from the air pressure.
 
Last edited by a moderator:
:stare1:

A $2.00 dead bolt from Freaknerds would a done just as well, and got you into the beer sooner.

;)
A simple padlock hasp on the outside would've worked too.

But I wanted to recreate the old shed door latch.

The only remaining guy I grew up with who isn't dead or in prison/rehab told me to do it this way. He's actually coming out here in a few days just to see it. It's like 30 miles.

Nostalgia.

For it to be identical to the one I made back in the day, I'd need to paint the outside of the door white, and find some dark blue carpet for the inside.

I almost bought gold metallic spray paint for the metal parts but said fuck it. I used some silver I already had.
 

Back
Top