Duck Pond Redneckery


Ok the gauge was a cunthair under 140 when I came in here and bumped the heat up from 60 to 68. It's been a while now, so...

View attachment 38617

Now it's a cunthair above 140.

So like 2 psi for 8 degrees of heat bump.

Probably not a linear scale though.

You asked for it!

Those temps are 288.7K and 293.15K (PV=nRT requires Kelvin,) so dividing those gives you 1.015. WAG on the pressure, say 139 psig, converts to 153.7 psia. Multiply by the ratio (1.015) and take the 14.7 for atmospheric pressure back out, gives 141 psig. So napkin numbers show the pressure increase roughly matches what theory predicts the gauge should read. Should be accurate to within a CH.
 
You asked for it!

Those temps are 288.7K and 293.15K (PV=nRT requires Kelvin,) so dividing those gives you 1.015. WAG on the pressure, say 139 psig, converts to 153.7 psia. Multiply by the ratio (1.015) and take the 14.7 for atmospheric pressure back out, gives 141 psig. So napkin numbers show the pressure increase roughly matches what theory predicts the gauge should read. Should be accurate to within a CH.
Keep in mind the ideal gas law doesn't take into account second order effects, and assumes an ideal model of the atom. Quantum effects are much messier, so if you're going to do anything that requires precision, you really need to use thermodynamic gas tables.
 
You could figure out what gage it is, and look up the code.

:rolleyes:

Kinda like you knew what yer doing...

;)
It's 6 gauge. I brought a little piece to Menard's. :D

I don't know how to use the wire gauge calculator.

Advanced Wire Size Calculator

Two hots, ten feet each. Connect either to a neutral and you have 120 volts. But it's 240 across the two.
50 amp breaker. No idea what the welder draws but whatever... Breaker and outlet are both 50 amps.

So,... 50 amps, 120 volts, ten feet, in a raceway... Coldest ambient, aluminum, No idea about voltage drop or jacketing, it says 6AWG.

Or go ya gotta go with the total loop back to the panel? That would be 20 feet. :dunno:

Or 240 volts? :dunno:

I'm going to use the 6 AWG aerial cable. If it melts, I'll rewire it.
 
Yeah, by multiple crews of guys who don't have to make 80 trips to Menard's because they bulk purchase all their materials.

No idea.

Gotta relocate the welder outlet, finish plywooding up the electrical closet, build a door for it then I'm gonna say **** it and go trucking for a while.
well hell multable crews of guys knows what gauge wires are to. and ofcourse they bulk purchase they get the shit cheap the more they buy the cheaper it is


though it's comming along good:thumbsup:
 
well hell multable crews of guys knows what gauge wires are to. and ofcourse they bulk purchase they get the **** cheap the more they buy the cheaper it is


though it's comming along good:thumbsup:
The electricians wouldn't know how to plumb up air lines any better than you or me.

The framers don't know how to hook up a furnace. (In fact most of them don't even know how to do framing. They're just nail gun operators.)

The furnace guy doesn't know how to install a drop ceiling.

I did all of that stuff. Even all the "two man operation" stuff.

I invented 5 tools, all of which I wouldn't have needed if I wasn't doing it all 100% by myself.

And with an insistence on doing everything "the right way" or at least in a manner that won't require redoing it later, it takes time.

I've seen how so-called "professionals" work.

You can either pay through the nose for a licensed, bonded, insured and overstaffed crew to do it right, or have Jim-Bob and Cletus fuck it all up.

I don't want strangers in here anyway. Especially the two clowns I was talking to at Menard's yesterday.

This one tooth hillbilly looking guy said he was an electrician. Pointed at a 3/4" knockout in an electrical box and said I could put 1" conduit to it. He demonstrated by holding a pre-bent 90 up to it.

I said "the hole needs to be larger to accommodate the fitting."

:bonk:

He was looking for a double box cover with a hole the size of the one for my air compressor outlet on one side and a rectangle for a GFCI on the other.

Ain't gonna find that.

I said get a blank cover, a hole saw and an electric jigsaw and make one. He asked what a jigsaw was. :rolleyes:

And he considers himself a professional electrician. :stare1:

I'm "just a dumb truck driver" and I know better than that. :confused:
 
Drain line. The red one that goes to the floor then into the wall again. It blows out across the floor. Good way to sweep half the shop floor. :D

20170208_012433.webp

Welder conduit.

20170208_012449.webp

Welder outlet.

20170208_012019.webp
 
I couldn't test it with the cover on. Tester leads aren't long enough. o_O

20170208_010243.webp

20170208_010439.webp

Menard's doesn't have 90° fittings for 1" conduit so I had to make my own.

Shoving the wires through it was a PAIN. IN. THE. ASS. :mad:


Menard's also doesn't have OSB plywood without spots all over it. :mad:
 
Lots of crap for a 28" wall. :rolleyes:

20170208_013415.webp

It ain't even done yet. The top is going to have the hose reel on it.

Here's where the drain goes back through. Menard's only had four of the 5" brass pipes so this is a 6" with a scrap of conduit as a spacer. :toothpick:

20170208_013639.webp

Yeah I butchered a brand new 50 foot rubber hose for that. Good ol' Harbor Freight. :cool:

It was either that or use some of the cheap poly crap that snaps in half if you breathe on it when it's cold. I've got a couple hundred feet of that crap. That crap is useless. o_O
 
Well this sucks. :(

Last minute change of plans..

Right as I was about to drill the hole for the brass pipe that feeds the hose reel, I remembered I'm taller than the Geezer.

He was in here so I held it up to the wall with the crank handle at the top of the rotation and he'd him stand there with his hand on the handle and feet flat on the floor.

A little pencil mark where the air pipe will go through, blah blah blah,.... and:

20170208_162529.webp

I wanted it higher than that. o_O
 
Drive nekkid... they'll get a hint and turn th' camera feed off.

;)
I'd like to have live access to one of those cameras so I can determine how close it can focus. Like if it can focus on something 6" away I'll print a panoramic view of an empty truck interior but with a mouse-drawn cartoon version of myself in the driver's seat. (kind of like in the beginning of that cartoon I made making fun of @Skateboard)

Tape it to something that'll hold it in a curved shape around the lens (it's a fisheye) at it's minimum focus distance.

Get out on the highway with an empty trailer and jam on the brakes to trigger it. Then just wait for the phone call ....

:stirpot2:
 
Ain't no way in hell I'm going to maneuver a properly notched, single piece of OSB into here. So I put that center piece in. I don't have any 2x6 left but this part is going to be half underneath the pallet rack shelf (which is currently disassembled) and doesn't need to be quintuple Godzilla strong.

20170209_170953.webp

20170209_202837.webp

Measuring around the obstacles and cutting them out is kinda like I'm making a jigsaw puzzle.

20170209_202711.webp

That's just set in place. Gotta take it off and put insulation in now. I don't like that part. :mad:
 

Back
Top