Duck Pond Redneckery


Just this:

View attachment 38387

Just 2x4s would be plenty strong enough to hold it because it's only a 38 inch span.

I just don't want it to sag over time. Or wiggle when I walk on it.

Half that floor will be unusable because it will be under the pallet rack shelf. So that will be single 2x6's spaced on 24's with 7/16 OSB on top. The half that's exposed and will have the air compressor on it will have the doubled joists, and two layers of 3/4 CDX plywood since the compressor sets on just 3 legs and is heavy.

I don't know how heavy it is but when I bear hug it, I can only lift it about an inch, though part of that is because it's awkward and top-heavy.
I think you'd be better off using short pieces of 2 x whatever under the legs on top of just one layer of OSB. It'll spread the weight better, and timber is better than OSB at handling the vibration. Plus you won't have to lift 2 sheets of glue 8' in the air.
 
I think you'd be better off using short pieces of 2 x whatever under the legs on top of just one layer of OSB. It'll spread the weight better, and timber is better than OSB at handling the vibration. Plus you won't have to lift 2 sheets of glue 8' in the air.
There's rubber pads under the legs.

But yeah, vibration is another reason it's being beefed up so much.

Lifting ONE sheet of 3/4 CDX plywood up over my head won't be a problem. Because it'll be cut in half. ;)

One sheet about 3-1/2 ft by about 5 feet will be screwed to the joists as the actual floor and I'll just put the scrap piece on top of that for extra weight distribution.

I don't want 2x_ attached to the compressor feet because the fasteners will stick out the bottom. Unless I recess them, and that won't leave much meat under the bolts. Lag bolts would work themselves loose probably.

I will have a V made of 2x4s under them while I lift it up there though.

The tractor bucket isn't big enough to fit all 3 feet on the flat bottom before it curves upwards in the back. So I gotta have it hanging like 3 inches over the edge of the bucket.

The plan is to make a V with a half-lap joint at the point, and put a grade eight 3/8" bolt through one leg, through the half lap and down through a drain hole in the bucket. The other two legs will be on the ends of the 2x4s that overhang the edge of the bucket, lag bolted through the feet. And those 2x4s will be C-clamped to the edge of the bucket.

When I get it up about 3 feet I'll be able to put straps around it so if it does tip over, it won't fall west and turn me into hamburger meat.

The top of that electrical closet "locker" will be about 7-1/2 feet. It's height was determined by the pallet rack shelf it has to fit under.

I already asked @Blood to be present during the lift just for extra redneck engineering expertise. My dad's suggestions so far have been stupid.

Except my dad did come up with the idea to use my shop vac and a long corrugated plastic hose to suck the tractor's exhaust fumes outside though. I'll just have to figure out a way to put an intermediate in there in case the heat melts the plastic. Once you get melted plastic on exhaust parts it stinks forever.
 
Last edited by a moderator:
There's rubber pads under the legs.

But yeah, vibration is another reason it's being beefed up so much.

Lifting ONE sheet of 3/4 CDX plywood up over my head won't be a problem. Because it'll be cut in half. ;)

One sheet about 3-1/2 ft by about 5 feet will be screwed to the joists as the actual floor and I'll just put the scrap piece on top of that for extra weight distribution.

I don't want 2x_ attached to the compressor feet because the fasteners will stick out the bottom. Unless I recess them, and that won't leave much meat under the bolts. Lag bolts would work themselves loose probably.

I will have a V made of 2x4s under them while I lift it up there though.

The tractor bucket isn't big enough to fit all 3 feet on the flat bottom before it curves upwards in the back. So I gotta have it hanging like 3 inches over the edge of the bucket.

The plan is to make a V with a half-lap joint at the point, and put a grade eight 3/8" bolt through one leg, through the half lap and down through a drain hole in the bucket. The other two legs will be on the ends of the 2x4s that overhang the edge of the bucket, lag bolted through the feet. And those 2x4s will be C-clamped to the edge of the bucket.

When I get it up about 3 feet I'll be able to put straps around it so if it does tip over, it won't fall west and turn me into hamburger meat.

The top of that electrical closet "locker" will be about 7-1/2 feet. It's height was determined by the pallet rack shelf it has to fit under.

I already asked @Blood to be present during the lift just for extra redneck engineering expertise. My dad's suggestions so far have been stupid.

Except my dad did come up with the idea to use my shop vac and a long corrugated plastic hose to suck the tractor's exhaust fumes outside though. I'll just have to figure out a way to put an intermediate in there in case the heat melts the plastic. Once you get melted plastic on exhaust parts it stinks forever.
you realize, each day when you have to drain the water out, you'll have to climb a ladder to do so..??

rubber feet mean nothing. it'll still vibrate. no garage i ever worked in, had an air compressor mounted on anything but the concrete floor.

but....you had chest pains, you're gonna die before you ever get this thing done.
 
Except my dad did come up with the idea to use my shop vac and a long corrugated plastic hose to suck the tractor's exhaust fumes outside though. I'll just have to figure out a way to put an intermediate in there in case the heat melts the plastic. Once you get melted plastic on exhaust parts it stinks forever.

Forget the shop vac. Just run a tube from the exhaust outside.

Ain't nuthin' complicated 'bout this...

:toothpick:

Unless yer lookin' ta die. :D
 
yep...he's gonna die


generate.php
 
Forget the shop vac. Just run a tube from the exhaust outside.

Ain't nuthin' complicated 'bout this...

:toothpick:

Unless yer lookin' ta die. :D
Too much back pressure in a long corrugated hose. It'll leak where it's attached to the tail pipe unless there's suction.
 
a long drain tube, should be a flexible type, as it will crack over time from vibration, especially if you mount it to the studs.
Yep. Rubber hose, valve on the wall, then another hose going outside.

I got a double throw 20 amp switch for the 240 volt outlet I'm going to put up there.
 
Yep. Rubber hose, valve on the wall, then another hose going outside.
i think PEX hose from where else, Maynerds, would have adaptors that you can install for draining, and the PEX will not rot out like ordinary rubber.

i don;t know the price of PEX, nor the adaptors.

never mind, i don't see drain valves for PEX
 
i think PEX hose from where else, Maynerds, would have adaptors that you can install for draining, and the PEX will not rot out like ordinary rubber.

i don;t know the price of PEX, nor the adaptors.

never mind, i don't see drain valves for PEX
From the valve to outside or wherever I decide to discharge it, I can use pretty much anything as long as I secure the end so it doesn't flop around all over the place from the jet propulsion.

I don't think rubber will dry rot indoors where there's no ultraviolet light on it.
 
From the valve to outside or wherever I decide to discharge it, I can use pretty much anything as long as I secure the end so it doesn't flop around all over the place from the jet propulsion.

I don't think rubber will dry rot indoors where there's no ultraviolet light on it.
the atmosphere will rot it out. check any tires in your shop, that you have had for a few years, they will be dry rotted. but a hose is cheap. no biggie. just don;t chance driving on those tires.
 
the atmosphere will rot it out. check any tires in your shop, that you have had for a few years, they will be dry rotted. but a hose is cheap. no biggie. just don;t chance driving on those tires.
The tires on my lawnmower are 2 years old and have always been in the barn except when mowing. And they're dry rotted.

The tires on my tractor are probably the originals from 1946 and they still hold air.
 
I got a deal today I bet you would love, about 600 lbs of welding rod for 40 bucks, the guy got them years ago at a yard sale most of the cans open and he said that they were damp and wouldn't weld right of course I didn't bother to educate him in the fact that all he had to do was bake the moisture out of them and they would be good as new which is what I am in the process of doing now
 
The tires on my lawnmower are 2 years old and have always been in the barn except when mowing. And they're dry rotted.

The tires on my tractor are probably the originals from 1946 and they still hold air.
the tires on your lawnmower, were prolly made in china

the tires on the tractor, were made in America when quality and materials were made here.
 

Back
Top