Duck Pond Redneckery


So basically I'm stuck until it either stops raining or I get the van fixed. I need another handful of 2x4's to frame out the locker and I don't mess with tarps.

Van's brake pedal went to the floor the other day and I ain't even bothered to investigate beyond noting that the fluid in the reservoir was not low.
 
20170117_211740.webp

20170117_213202.webp

20170118_000320.webp

There's no redacted reason for this old hunk of redacted asterisks not to start.

It's seriously pissing me off.

It's not too cold. Battery is junk but I was feeding it like 80 gazillion amps and it was cranking fast. It's got gas... Probably no spark.

And with both the grader blade and the loader on the ground it's actually easier to winch a bobtail through wet grass. I know because I've done it using the same cable ratchet. The bottom of the bucket snagged on something and ripped a chunk of sod out of the ground.
 
I'm not buying another 6 volt battery for that thing.

It's got a generator... No voltage regulator.

The voltage regulator is a flat-head screw on the back of the generator.

To use the headlights you gotta turn them on and hook up the voltmeter and crank it up to about 7 volts at half throttle. Otherwise they'll drain the battery.

If you forget to turn it back down, it'll be pushing 9 volts and boil the battery. :mad:

12 volt positive ground conversion kit is $100.

You get an alternator w/internal regulator, bracket and wiring harness.

The 6 volt starter is fine, just gotta swap the two cables or it'll run backwards.

Yep. I'm gonna do the conversion. It'll give me an excuse to remove the hood and gas tank, check out the points, cap & rotor and fill the spark plug holes with kerosene. Probably sand and paint the hood while it's off.
 
View attachment 38250

View attachment 38251

View attachment 38252

There's no redacted reason for this old hunk of redacted asterisks not to start.

It's seriously pissing me off.

It's not too cold. Battery is junk but I was feeding it like 80 gazillion amps and it was cranking fast. It's got gas... Probably no spark.

And with both the grader blade and the loader on the ground it's actually easier to winch a bobtail through wet grass. I know because I've done it using the same cable ratchet. The bottom of the bucket snagged on something and ripped a chunk of sod out of the ground.
how is the distributor cap, and rotor.>??? is there good contact between the 2..???

have you tried cranking it over, in a dim light, to see if any spark runs down the side of the cap, (carbon tracking) or any wires bleeding the spark, to ground....>??

are the points adjusted correctly? is the condenser good..?? all these things can be the cause of a no start. is there an "electronic" ignition distributor you can get for that.>???

instead of K-1, i'd try Marvel Mystery Oil instead, in those cylinders.let it sit at least, over night.
 
how is the distributor cap, and rotor.>??? is there good contact between the 2..???

have you tried cranking it over, in a dim light, to see if any spark runs down the side of the cap, (carbon tracking) or any wires bleeding the spark, to ground....>??

are the points adjusted correctly? is the condenser good..?? all these things can be the cause of a no start. is there an "electronic" ignition distributor you can get for that.>???

instead of K-1, i'd try Marvel Mystery Oil instead, in those cylinders.let it sit at least, over night.
No idea.

It sat outside for months. And most recently its been rained on for three days straight, after first being laminated in ice.

I figure I'll just winch it into the shop and see what happens today after it's dried out and been on the slow charger overnight.

Getting to the points is a pain in the ass because it's on the front between the block and the radiator. Not impossible but just enough of a pain in the ass I'm not doing it outside in the cold and rain, while kneeling in gravel and mud.




Just getting it into the shop was a project in itself.

I called the geezer to help push it thinking we could simply set strips of metal under the grader blade and push on the tops of the rear tires for a 2:1 ratio but that was pointless.

I figured "well how much force can it possibly take to roll a 3000 lb machine horizontally onto cement?" so at first, because my workbench was screwed to the wall I'd just clamp the tow strap in the vise.

Ripped the whole damn workbench off the wall. :mad:

So I had that big heavy angle iron. I cut about an 8" piece and drilled one side for lag bolts and put a half inch hole in the for something to hook to.

I knew that I'd eventually need an anchor point for winching big heavy things into the shop anyway. Gonna have to do that to get the old F-100 in there to replace its gas tank and fuel lines.

That post is directly across from the door and it's set 6 feet into the ground and surrounded with concrete. So it's perfect. And I was able to rearrange the tool boxes so it's not in the way. It fits right between my two red ones.
 
Stubborn ol' cuss, ain't it?

:biglaugh:
Well it was manufactured in the same year we nuked Japan, so... yeah it's pretty old.

Still tough as nails though, when it starts.

That loader will pick up the ass end of a pickup truck and drag it around on its front wheels. I discovered that one day when I was plowing snow and I was too lazy to go in the house to get the keys to my ranger.

It lifted it like it was nothing, so I tried it on an old full size Chevy we used to have, and it lifted that too.

And I've yanked 18 wheelers out of my icy parking spot plenty of times.

One time I had the chains hooked too high on the 3 point hitch and the tractor did a wheelie. When I stepped on the clutch, it was probably close to 45 degrees and slammed down on that front axle and nothing broke.
 
Just for the hell of it I hit the starter on the tractor and it fired right up. Immediately too.

I guess it just needed to dry out.
 
Just for the hell of it I hit the starter on the tractor and it fired right up. Immediately too.

I guess it just needed to dry out.
i'd still spray the ignition system with silicon or WD 40. best however, to replace the cap, rotor, wires. dampness may be seeping in thru the cap, if it is porous.
 
i'd still spray the ignition system with silicon or WD 40. best however, to replace the cap, rotor, wires. dampness may be seeping in thru the cap, if it is porous.
Yep.

Or I can just stop leaving it outside in the rain.

Been planning on getting one of those carports you see everywhere. That won't protect it from light fluffy snow, or keep it warm but it'll be a good place to park it in the summer when I don't want it taking up half the workshop.


I just turned it around to get the front end closer to the tools, and I parked it with the bucket tipped down on it's edge to save floor space and grant me access to the front of the tractor so I can get at the distributor.

20170118_154722.webp

Discovered two things.

One, the skid strips are coming off the bottom of the bucket. The center one is totally off and it was what wedged into the ground and made it so hard to winch into the shop.

In hindsight I probably could've pressurized the suction side of the hydraulics with the air compressor and pulled the lever to raise the bucket without the pump running. I've never tried it with the engine off but I've done it to force fluid into the pump when it was below zero and wouldn't gravity feed.

20170118_154255.webp

20170118_154230.webp

The other thing I noticed is it appears that the bucket can be converted to a 3 foot wide snowplow by removing 9 big bolts.

And @Mike, whatever you just did to put the attachment upload progress bar in there, :thumbsup:
 
Last edited by a moderator:

Back
Top