Duck Pond Redneckery


It's shipped as three big beams & a box of bolts.

Assemble it on the shop floor, then get a bunch of Amish guys to stand it up using ropes and horses.

You putting in a trap door and the rail for the pulley to ride to get the rope to the horses?:toothpick:
 
You putting in a trap door and the rail for the pulley to ride to get the rope to the horses?:toothpick:
:dunno:

I ain't planned that far ahead yet.

I find that if I plan everything out ahead of time, nothing ever actually gets done, except lots of drawings on paper.

Which is how this happened:

20161102_021940.webp

For the south wall I gotta run the foam board insulation up to that 2x4 that's just above the ceiling, then run the plywood up to that 2x4.

I'll either have to lift those ceiling panels to get in there to screw the plywood to it, and hope the insulation falls back into place, or monkey around up above it all with 4 foot joist spacing. :stare1:
 
Ok so I made the ceiling fan thingy to securely hold a box 8-1/2" below the rafters.

20161103_201036.webp

20161103_192605.webp

That flat stock is welded to the box because I don't trust screws or even lag bolts going into the end grain.

Strapped on all 4 sides to lock it against motion in all directions if something (like a ladder I'm carrying while drunk) hits the fan and breaks a blade off & it starts wobbling like crazy or something. And of course I had to spray paint it because I burned off all the zinc.

Here's a mock-up. Can't secure it to the wood I put up across the trusses til I get the ceiling panel cut & in place & all that crap but my back is killing me for some reason.

20161103_201612.webp

The height & the east/west is perfect but the north/south positioning will have to wait til the ceiling panel is in place.

And I gotta hook up the flexible conduit at the box above it first.

And take some Aleve. Or morphine . . . o_O
 
The drop rod for the ceiling fan. Extended by one foot. Blades will be roughly 2 ft from the ceiling.

20161103_201019.webp

That's flexible conduit on the floor behind it. Looks kinda weird. Bad angle.

I simply cut it & welded in one foot of plumbing pipe. Other an odd size, slightly smaller than the pipe. So I couldn't just drill holes in the ends of the pipe.
 
After bolting that thing in it still wiggled about 1/8" east/west so I added another 2x4.

Looks stupid but it's rock solid in all directions. :thumbsup:

20161103_233315.webp

20161103_233940.webp

20161103_234121.webp
 
The drop rod for the ceiling fan. Extended by one foot. Blades will be roughly 2 ft from the ceiling.

View attachment 37176

That's flexible conduit on the floor behind it. Looks kinda weird. Bad angle.

I simply cut it & welded in one foot of plumbing pipe. Other an odd size, slightly smaller than the pipe. So I couldn't just drill holes in the ends of the pipe.
something like this:confused-96:

bigassfans_hangingaround_americanchopper.webp
 
if you really wanna get fancy you can install a mini split system and run em off of solar since there not power suckers. a 6000-12000 BTU unit will only draw about 9.6 amps maxed out in heat mode cooling mode is less

 
The drop rod for the ceiling fan. Extended by one foot. Blades will be roughly 2 ft from the ceiling.

View attachment 37176

That's flexible conduit on the floor behind it. Looks kinda weird. Bad angle.

I simply cut it & welded in one foot of plumbing pipe. Other an odd size, slightly smaller than the pipe. So I couldn't just drill holes in the ends of the pipe.
put real A/C in there and not that 1908 shit:D
 
No. More like this.

20161104_010302.webp

20161104_010613.webp

Ain't no blades on it yet cuz they'd be in the way while I do the other center lights &the next couple rows of ceiling panels.

Especially in the way because they'd be spinning. :mad:

This:

20161104_005450.webp

That's the 3-way switch for the fan. The pull chain is missing. :mad:

I didn't even notice til after I put it up.

I gotta get another one or butcher one of the other ceiling fans I've got laying around.

I don't know what speed it's stuck on.
 
No. More like this.

View attachment 37185

View attachment 37186

Ain't no blades on it yet cuz they'd be in the way while I do the other center lights &the next couple rows of ceiling panels.

Especially in the way because they'd be spinning. :mad:

This:

View attachment 37190

That's the 3-way switch for the fan. The pull chain is missing. :mad:

I didn't even notice til after I put it up.

I gotta get another one or butcher one of the other ceiling fans I've got laying around.

I don't know what speed it's stuck on.
Looks good
don't tell me you would have the fan going while putting up the ceiling and finishing off the lights. only you would do something like that :D. why butcher old fans when you can goto home depot or lowes and pick a new switch up for 5 bucks:confused-96:??? if it's made in china forget about fixing it:rolleyes:. that shit's ment to be thrown away and i am thinking so that people spend more money and it keep recycling up
 
Last edited:
Looks good
don't tell me you would have the fan going while putting up the ceiling and finishing off the lights. only you would do something like that :D. why butcher old fans when you can goto home depot or lowes and pick a new switch up for 5 bucks:confused-96:???
Do they sell those switches? That's the thing. If they do, then cool.
 
Yeah I'll just go to Menard's tomorrow.

I'm going to need one more of those 12 foot T-channels.

I measured one and marked it at 94". Then I cut it at 94". But as soon as I cut it, it shrank to 88". It was either a tape measure malfunction or the damn thing actually shrank right after I cut it. I should get a new tape measure too.:toothpick:
 

Back
Top