Who has oldtimers again?Geezer's reply:
I could actually do it. Wanna bet?
I forgot it's a convertible.![]()


the HVAC system will be another chapterOk, this still makes no sense at all why your doing this. Your closing off an uninsulated section of your barn that's 13' tall which your going to heat. Your not going to heat it I can tell you that' Closing it off does nothing unless the walls and ceiling are insulated. Even if they were that place is still going to be freezing. You said you needed something that was 13' tall. Why? You have a standard door on the room. Not like your going to drive a semi through it let alone a riding mower with a deck attached. Are you going to be working on cell tower poles or something? As far as I can tell you've wasted a lot of time and money on nothing other then enclosing an igloo within an igloo. I can assure you from first hand experience that one of those torpedo heaters is not going to heat the place. Been there, done it on an uninsulated 16x20 garage. The only thing it accomplished was a massive headache.
Now if it were me I would have picked a corner and built maybe a 16x16x8 workshop that was insulated and had decent heat like an 8' section of electric baseboard heating. In the dead of winter when it's cold out you just can't waltz into a workshop that's -20 and turn the heat on. Same as a truck or even your house. The thermometer may say 72 inside but it's F****ing cold. Everything is just plain radiating cold cold cold. My wood shop in the basement was the same until I put fins on the hot water pipe running through the shop upstairs for the forced hot water heating of the living room. My glue didn't freeze or anything else. It was always nice and toasty in there. That shop was maybe 16x16 or 20x20, can't remember but I insulated all the walls. The ceiling was already insulated.

Ok, this still makes no sense at all why your doing this. Your closing off an uninsulated section of your barn that's 13' tall which your going to heat. Your not going to heat it I can tell you that' Closing it off does nothing unless the walls and ceiling are insulated. Even if they were that place is still going to be freezing. You said you needed something that was 13' tall. Why? You have a standard door on the room. Not like your going to drive a semi through it let alone a riding mower with a deck attached. Are you going to be working on cell tower poles or something? As far as I can tell you've wasted a lot of time and money on nothing other then enclosing an igloo within an igloo. I can assure you from first hand experience that one of those torpedo heaters is not going to heat the place. Been there, done it on an uninsulated 16x20 garage. The only thing it accomplished was a massive headache.
Now if it were me I would have picked a corner and built maybe a 16x16x8 workshop that was insulated and had decent heat like an 8' section of electric baseboard heating. In the dead of winter when it's cold out you just can't waltz into a workshop that's -20 and turn the heat on. Same as a truck or even your house. The thermometer may say 72 inside but it's F****ing cold. Everything is just plain radiating cold cold cold. My wood shop in the basement was the same until I put fins on the hot water pipe running through the shop upstairs for the forced hot water heating of the living room. My glue didn't freeze or anything else. It was always nice and toasty in there. That shop was maybe 16x16 or 20x20, can't remember but I insulated all the walls. The ceiling was already insulated.

Yeppers. This will work perfectly. And if I can keep the floor clear of junk I can move it around from up top just by grabbing the rafters and pulling.
View attachment 37119

Yes I know it's nothing but it did heat it. Even at night. It was the regular hangout place until I took over the shed which was smaller.35k BTU is NOTHING! F***, an Espar is like 15k. Like to see that heat your garage.
I already explained that.But why over 13' high????
I already explained that.
Here: https://www.truckersforum.net/forum/threads/duck-pond-redneckery.86547/page-45#post-563147
Last paragraph.
isn't insulation supposed to be having a plastic vapor barrier..???
isn't insulation supposed to be having a plastic vapor barrier..???

you can get cancer from it.Crystalline Silica . . . WTF is that?
There's no MSDS with these ceiling tiles, just a warning label. Says don't snort it like come or you'll die or something.
Whatever though. I held a cigarette lighter to a little piece of the insulation. It turned black but that's all that happened after like 30 seconds of flame directly on it.
Then I did the same thing to a scrap of ceiling tile. Since the stupid T channels don't have the first of the 4 foot slots for the little 2 foot cross pieces right at 4 feet from the end I'm having to cut all the panels at the north end down to 43-5/8". So I took one of those scraps and held the lighter to it.
The white face immediately turned black and after about 30 seconds it started smoking a little bit but it never started burning by itself.
Says don't snort it like come or you'll die or something