Duck Pond Redneckery


What's wrong with the Chinese garlic?

I know about the horrible, unsanitary & downright filthy conditions they raise (and taint) seafood in for sale to the USA thanks to our politicians who sold our food industry to China via TPP but what could they do to seeds to make them grow poisonous food? :confused-96:
Seeds, throw 'em in the ground.... Isn't that the same thing as "planting" them?

:bonk:

I have some cloves from that same bloodline but they were picked prematurely & they're small.
the chinese garlic does not grow well, (here) but that aside, the taste of chinese garlic just isn't the same. the chinese farmers are not as well versed in farming, using all sorts of insecticides and fertilizers we would not use here, like sewage, and human waste. probably one of the few reasons, they are short people.
 
Hey @Blood remember that thing I made out of sheet metal for holding aerosol cans on my workbench that I'm too lazy to go get a picture of?

This seems way simpler. Just not as compact and it doesn't double as a thing to clip tape measures on. But you can put nails or hooks for things on it.

14484627_561405707317944_6442017685799052611_n.webp

Looks like one pallet makes 4 of them. Just gotta rip apart another pallet for the bottoms.
 
This is how I'm attaching the wall to the pallet rack without applying the weight of the wall to the racks. Just clamping it to hold the wall upright and tight against it, but the weight of the wood will be on the cement floor.

20161004_184548.webp

20161004_185409.webp

Didn't need to countersink the holes on the short piece but the scraps of threaded rod I used were a half inch too short.

The holes in the longer 2x4's do need countersunk so the plywood will fit flush against it.
 
Even though my plumb bob is just a piece of mason line tied to a C-clamp with a padlock hanging at the bottom, according to gravity, this 2x4 is 100% dead on balls true and plumb. ;)

20161004_213107.webp
 
Ran outta washers & threaded rod.

But I cut all the spacers I need to finish. Not gonna bevel them. I only did that because I was running low on washers. ;)

20161004_215100.webp

20161004_224051.webp
 
Wait. You mean they're not supposed to be cockeyed? :headscratch2:
The pallet rack leans east 1" over its height of 14 ft but is perfect north/south.

The barn post beside the end of the rack wall is perfectly vertical.

I tried to straighten the rack wall with diagonal ratchet straps but I had it so tight I thought I was gonna break the ratchet & it hadn't budged. So I'm building the wall to be perfectly square & plumb.

Also I don't know if wind pressure makes the wall post move in & out so I'm going to use a narrow strip of barn siding to connect the wall to the post. The corrogation will flex if the post moves.
 
Flat stock is expensive.

Conduit is cheap. :)

20161005_185700.webp

How to build a 14 foot tall wall entirely by yourself because your helper has senioritis & has wandered off and is flying a kite with a fishing pole while riding a bicycle..

20161005_200901.webp

20161005_200835.webp
 
Because Menard's isn't open at 2AM....

20161007_233617.webp

Crushed 1-½ conduit, welded in a T on both sides. And drilled for screws.

20161007_233734.webp

Grind the weld on the side that goes against the wood

20161007_235100.webp

If you're really careful you don't have to wait for the paint to dry. ;)

That stuff was still sticky 4 hours after I put it on the wood.
 
Clamping the studs to the horizontal beams because I want it to be able to slip. I want the weight of the shelves transferred to the steel uprights, not the wooden wall. Some of those beams don't sit all the way down in the slots until you put weight on them. So no screws or bolts into the beams.

The clamps are tight for now, to keep them perfectly straight. But once I lock them in place with the plywood I'm going loosen them and let the weight of the wood settle so it's supported by the floor, then tighten them back up, just a little bit beyond finger-tight.

20161004_192635.webp

20161007_222310.webp

Half inch conduit spacers at the bottom keeps the short 2x4 vertical.
 
Last edited by a moderator:
But I tried something different for one clamp. Figured it's less ugly.

20161007_193716.webp 20161007_213737.webp

But it ended up taking about 3 times as long to make that than to make them with 1 foot pieces of 2x4.
 
Got the wall framed out, up to the door.

Gotta go get a door so I can continue.

Geezer is funding 90% of this project but he got Senioritis & wandered off in his Mazda Miata. Last I heard he was in Moberly, MO. :coocoo:

I might just make a door from scratch.

Luan underlayment sandwiched over foam insulation with a perimeter of 2x4.

20161008_033651.webp

20161008_033709.webp

Gotta get masonry bolts to hold the bottom in place.

20161008_033749.webp

Different type of clamp because the door post is 5" thick. Just hold back the bolt and turn the lock nut to tighten it.

I couldn't feel much resistance with the wrench & didn't hear wood creaking as I tightened it like I did with all the other clamps & I ended up bending the angle-iron. :confused:

Thinking about taking it off and painting it. It was 3AM when I did that and the Red Bull was wearing off.
 

Back
Top