Duck Pond Redneckery


It was Humphrey Bogart's name and that is where the term Bogart came from.
Yeah but I'm talking about the manufacturer of that "Tri-metric" thing.

Which I've just made a stowing location for.
This is where it hangs out when it's not in use.

20170809_220958.webp

I was just gonna hang it on the belt nut figured what if some idiot pulls the starter rope...

20170809_201104.webp
 
I actually have a 4G signal here at the state line. About 100 feet into Indiana. Usually it's a dead zone.

Anyway... Minn Kota claims 42 amps.

20170810_161711.webp

Maybe at 16 volts or something..

I tested it with a single raft.

20170810_161757.webp

Here's the numbers I got.

Engine off, motor on
speed 1: 7.8 amps
Speed 2: 9.6 amps
Speed 3: 13.6 amps
Speed 4: 17.2 amps
Speed 5: 35 amps
Speed 5 with seaweed on the prop: 37 amps

After about 20 minutes, I started the generator. Some old guys were fishing by the launch so I waited til I was a little ways away.

Engine on, motor off. Initial charge was 50 amps, then tapered off to 28 amps after 1 minute.

It remained at 28 amps when I put the trolling motor on speed 5 which means the alternator is capable of delivering at least 63 amps.

After a few minutes the rate of charge had dropped to 12.7 and I was approaching the bridge to measure the clearance and people were fishing off it so I shut it off.

Between the I-beams it's 42-1/4" from the steel rods to the surface of the water.

From the bolts on the bottom of the I-beams it's 29-1/4"

The USGS hydrological service meter in Momence is reporting 2.08 feet of depth at the meter.

So with this info I can now make reasonably accurate estimates of the bridge clearance before I even leave home. :thumbsup:
 
Under the Bridge

20170810_160548.webp

20170810_160554.webp



Seaweed. Even in that center channel. Trolling motor has a prop designed for chopping seaweed but that shit got thick. This was in Indiana, looking northwest into a side channel. I went through there, around an island that looks to be about 2 acres, then looped around to the main channel and measured the bridge clearance.

20170810_161409.webp
 
Under the Bridge

View attachment 41372

View attachment 41373



Seaweed. Even in that center channel. Trolling motor has a prop designed for chopping seaweed but that **** got thick. This was in Indiana, looking northwest into a side channel. I went through there, around an island that looks to be about 2 acres, then looped around to the main channel and measured the bridge clearance.

View attachment 41374

I found the troll!:thumbsup::rolllaugh:
 
So this beefy A-frame tongue, with heavy C-channel in the middle, is Armageddon proof... Except some jackass welded it to the sidewall of 2" x 3" square tube. I always assumed it was thicker stuff than the main rails which I can see at the front is 14 gauge.

No, it's not. It's the same stuff. o_O

20170811_173432-jpg.41395


The front crossmember, also forms the base of the triangle. It's thin wall hollow square tube. Nothing passes through it.. That beefy stuff in the middle with like half inch thick gussets... All welded to the thin-wall square tube. No reinforcement plates across the top and bottom either.

:bonk:

Strong when the load is applied like normal but not when you weld only to the sidewalls.

I noticed it bouncing in the front way more than usual so I got the old man to pull over. I spotted a crack in the outer corners and said we gotta abort cuz it ain't making it down that crappy pothole filled state line road.

Got it home and put it in the shop. Got under it and the whole damn bottom was splitting open. :eek:

I sanded it to bare metal and welded it up with the torch.

Then I did this:

20170811_225111.webp

Tomorrow I'm gonna probably put some kind of X's down the whole thing. Or just one section, I dunno.... It can still flex that square tube if the whole racks skew.

It's designed for airplane wings. It came with a plane my dad bought in like 1988. Maybe the rafts are too heavy for it.... Actually I bet it was that cooler... That trip 2 weeks ago when I strapped the cooler on the rack near the front... Brian thought we needed 76 beers, 2 big bags of ice, and two cases of water. It took two of us to lift it. I had it on the passenger side and that's where the crack started and was pulled 1/8" apart. :rolleyes:
 
"we needed 76 beers, 2 big bags of ice, and two cases of water. It took two of us to lift it. I had it on the passenger side and that's where the crack started and was pulled 1/8" apart. :rolleyes:"

Get a roller skate trucker....That lil ginny you got ain't gonna get the job done....:rolllaugh:
 
All the "lakes" around there are in one of three categories:
  1. Abandoned quarry
  2. Abandoned strip mine
  3. A hole dug to steal dirt for the highway overpass.
Well, except Lake Michigan. And if you take the raft out on that, we want video!
One single 4x8 raft can handle anything Lake Michigan can throw at it. I'd bet large sums of money that it would take a big cresting tidal wave to flip it, like the ones you see in the pictures of surfers in Hawaii.

Whether I could remain on it in a storm is a completely different question though. ;)

Multiple rafts connected together, I dunno. I got away with just 1x4's tying two rafts together inline for years... I'd simply screw them together with drywall screws. And they were cedar, not pine. But I never used them in water where there are big displacement hull power boats that make wakes... Not because the 1x4's might snap if I hit a big wave head-on with lots of weight on the raft, but because I deliberately avoid water deep enough the big fancy boats can go because those are the areas patrolled by the Water Nazis who prey on people like me who never make even the slightest efforts to comply with their idiotic laws.
 
Last edited by a moderator:
On I-55 northbound you go over the Kankakee just after the exit for that pay-to-park and the new Loves or Petro or whatever that is. Then 2 miles later you go over the Des Plaines on that iron bridge.

The two rivers join and form the Illinois River about 2-3 miles west of I-55.

Starting on the "Chicago Ship & Sanitary Canal" in Chicago, it's maintained by locks and dams to Joliet where it merges with the Des Plaines, then on to St Louis, etc.

The water level is maintained within reason, even back upstream on the Kankakee to the Wilmington dam.

Because of the flood control effects, houses along the river below the Wilmington dam are expensive rich snob houses.

From Wilmington up to the Kankakee dam I don't know about, but from Kankakee to the Indiana state line it's natural and prone to flooding. So the houses are cheaper. Blue collar people.

Below the Wilmington dam, NOBODY in big power boats with 5 and 6 digit price tags slow down past kayaks, canoes, little fishing boats, etc. Rich snobs don't give two shits if they swamp those whom they perceive as "poor". There's also Water Nazi patrol boats who harass people in canoes for not having a sticker or a whistle while totally ignoring the trust fund babies going 50 mph past a marina while drunk, and doing donuts in front of oncoming barges.

From the state line to Momence, I've never seen a single person NOT slow down and idle past the canoe and kayak people.

I've also never seen any Water Nazi boats there. I did see a conservation boat there once but they were using it as a tractor to drag a fallen tree out of the main channel. Doing a public service instead of being a menace.
 
I vaporized a Sawzall blade cutting through conduit containing power cables with raw power from the utility grid today. :eek:

So my dad's friend Rita owns three houses in Manteno.

Her sons Mike and Terry live in the other two.

Mike's double wide is fed power via underground to a little post next to the trailer, with a meter and a shutoff box.

Terry's is aerial, the wires run through Mike's trees across his yard. :coocoo:

Anyway, 10 years ago Mike's was aerial too, with a pole on his property. Mike's was put underground and Terry's aerial straight from the pole on the street. Same day.

2 weeks ago a storm knocked over that old abandoned pole on Mike's property. The mast head thing has wires that are obviously cut at the top. It's leaning on a small limb in the tree and will hit the double wide if it falls so I secured it with ropes.

I started cutting the conduit near the ground and it sparked and melted the Sawzall blade. :eek:

I looked at Mike's meter box and it only has two hots and a neutral from underground, the meter, then the switch, then into the trailer. I pulled that master and the damn thing blew out another Sawzall blade.

WTF???

I looked at Terry's house and his aerial power comes in at the top of mast on his house, then down to the meter in conduit. From the meter to the ground is another conduit. The ground, I assumed...

I went and opened his meter box and there's the feeds from the aerial, and on the house side of the meter, old copper sharing those lugs and going into the conduit that goes underground. Unswitched hots straight from Terry's meter...

So I asked Rita when she bought Terry's house. "ten years ago"...

Rita bought Mike's trailer first, like 35 years ago, from the guy who owned Terry's.. He owned them both and was renting out the trailer before he sold it to her.

Then ten years ago he sold her Terry's house but insisted that ComEd redo the power feed first.... o_O

That year, she was living in the trailer and her dad died.. She inherited his house and money and bought the house next door for Terry and gave Mike the trailer. And the seller insisted on replacing the power feed to Terry's house before closing.... And then ComEd said they had to redo the trailer too for some reason ... o_O

Mike is 39 years old and has never had a job in his entire life.... Ever. So I know she's paying the electric bill....

I said "let me guess... Immediately Mike's electric bill dropped considerably"

Yep...

She just assumed that the occupancy going from 4 people to 1 would account for the bill dropping....

Um... No.

It's because the guy who sold you this trailer was stealing electricity from you for 25 years until he sold you Terry's house... He didn't have ComEd "redo" anything, he simply established service to it. When he owned both properties he had them on a single meter. The feeds from his meter to his house were jumpered to the feeds from the trailer and there simply was no feed to his meter from the grid.

And the lineman who did it was a moron who left the feed from Mike's old meter hooked up via underground, on the house side of the meter. He probably thought they went to the garage.

So there's unswitched feeds basically straight from the grid running into that old abandoned pole and meter box that I was told was disconnected in 2007. :confused:

She's having ComEd come out Monday to disconnect them in Terry's meter box so I can finish removing that old pole from Mike's yard. o_O

So she was paying her neighbor's electric bill for 25 years and didn't know it. :eek:

Probably too late to sue the bastard. :mad:
 
Last edited by a moderator:

Back
Top